EN - 61
For other configurations, refer to the communication protocol document.
Hexadecimal bit
No.
Decimal bit
No.
Description Type Setting
0x82 to 0x9f free (continued)
0x117 279 Compressor 2 discharge sensor fault Read-only 1 = Fault
0x118 280 Not used
0x119 281 Circuit 2 HP sensor fault Read-only 1 = Fault
0x11a 282 Circuit 2 LP sensor fault Read-only 1 = Fault
0x11b 283 Circuit 2 suction sensor fault Read-only 1 = Fault
0x11c 284 Circuit 2 liquid sensor fault Read-only 1 = Fault
0x11d 285 ADD3 board link fault (circuits 1 and 2) Read-only 1 = Fault
0x11e to 0x13f reserved
0x140 320 Compressor 2 load shedding Read-only 1 = Load shedding
0x141 321 Not used
0x150 336 Circuit 3 fault summary Read-only 1 = Fault
0x151 337 Compressor 3 fault Read-only 1 = Fault
0x152 338 Not used Read-only 1 = Fault
0x153 339 Circuit 3 manual HP fault Read-only 1 = Fault
0x154 340 Not used Read-only 1 = Fault
0x155 341 Circuit 3 LP fault Read-only 1 = Fault
0x156 342 Circuit 3 water freeze fault Read-only 1 = Fault
0x157 343 Not used Read-only 1 = Fault
0x158 344 Not used Read-only 1 = Fault
0x159 345 Compressor 3 discharge fault Read-only 1 = Fault
0x15a 346 Not used Read-only 1 = Fault
0x15b 347 Not used Read-only 1 = Fault
0x15c 348 Expansion valve fault, circuit 3 Read-only 1 = Fault
0c15d 349 Not used Read-only 1 = Fault
0x15e 350 Circuit 3 low superheat fault Read-only 1 = Fault
0x15f 351 Circuit 3 high superheat fault Read-only 1 = Fault
0x160 352 Circuit 3 desuperheat fault Read-only 1 = Fault
0x161 353 Circuit 3 lubrication fault Read-only 1 = Fault
0x162 354 Not used Read-only 1 = Fault
0x163 355 Not used Read-only 1 = Fault
0x164 356 Not used Read-only 1 = Fault
0x165 357 Not used Read-only 1 = Fault
0x166 358 Not used Read-only 1 = Fault
0x167 359 Compressor 3 discharge sensor fault Read-only 1 = Fault
0x168 360 Not used Read-only 1 = Fault
0x169 361 Circuit 3 HP sensor fault Read-only 1 = Fault
0x16a 362 Circuit 3 LP sensor fault Read-only 1 = Fault
0x16b 363 Circuit 3 suction sensor fault3 Read-only 1 = Fault
0x16c 364 Circuit 3 liquid sensor fault Read-only 1 = Fault
0x16d 365 ADD3 board link fault (circuit 3) Read-only 1 = Fault
0x16e 366 ADD1 board link fault (circuit 3) Read-only 1 = Fault
0x16f 367 Not used Read-only 1 = Fault
0x170 368 Read-only 1 = Fault
0x171 to 0x17f reserved
0x180 384 Compressor 3 load shedding Read-only 1=Load shedding
To Previous Page
Loading...