No FPD image version upgrade is required if the status of the power module is CURRENT in the command
output.
Example:
sysadmin-vm:0_RP0# show hw-module fpd
Wed Feb 28 03:35:09.566 UTC
FPD Versions
===============
Location Card type HWver FPD device ATR Status Run Programd
-------------------------------------------------------------------------------
0/0 NCS1002-K9 0.1 CTRL_BKP_LOW B CURRENT 2.23
0/0 NCS1002-K9 0.1 CTRL_BKP_UP B CURRENT 2.23
0/0 NCS1002-K9 0.1 CTRL_FPGA_LOW CURRENT 2.23 2.23
0/0 NCS1002-K9 0.1 CTRL_FPGA_UP CURRENT 2.23 2.23
0/RP0 NCS1K-CNTLR 0.1 BIOS_Backup BS CURRENT 14.00
0/RP0 NCS1K-CNTLR 0.1 BIOS_Primary S CURRENT 14.40 14.40
0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_BKP BS CURRENT 0.15
0/RP0 NCS1K-CNTLR 0.1 Daisy_Duke_FPGA S CURRENT 0.17 0.17
0/PM0 NCS1K-2KW-AC 0.0 PO-PriMCU NEED UPGD 0.00 0.00
0/PM1 NCS1K-2KW-AC 0.0 PO-PriMCU NEED UPGD 0.00 0.00
In the above example, the status of both power modules is NEED UPGD. This status confirms that an FPD
image version upgrade is required. If the power cable is not connected to a power module, the Running version
of the power module is displayed as 0.0.
Ensure that both power cables are connected to the power modules during the upgrade procedure.
Caution
Step 2 Use the show fpd package command to display the FPD image version you need for each hardware component.
Example:
sysadmin-vm:0_RP0# show fpd package
Wed Feb 28 03:35:19.382 UTC
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
NCS1002 CTRL_BKP_LOW YES 2.23 2.23 0.1
CTRL_FPGA_LOW YES 2.23 2.23 0.1
--------------------------------------------------------------------------------
NCS1002 CTRL_BKP_UP YES 2.23 2.23 0.1
CTRL_FPGA_UP YES 2.23 2.23 0.1
NCS1002--RP BIOS_Backup YES 14.00 14.00 0.1
BIOS_Primary YES 14.40 14.40 0.1
Daisy_Duke_BKP YES 0.15 0.15 0.1
Daisy_Duke_FPGA YES 0.17 0.17 0.1
--------------------------------------------------------------------------------
Step 3 Use the upgrade hw-module command to upgrade the FPD image of the power module.
Example:
The following example shows how to upgrade the FPD image of the power module.
sysadmin-vm:0_RP0# upgrade hw-module location 0/PM0 fpd PO-PriMCU
Step 4 Use the show hw-module fpd command to verify the upgraded firmware version of the power module.
System Setup and Software Installation Guide for Cisco NCS 1002
59
Perform System Upgrade and Install Feature Packages
Upgrading the Firmware Version of Power Modules
To Next Page
Loading...
Need help?
General
