Cisco NCS 1002 System Setup And Software Installation Guide

The following example shows the output of show fpd package command before FPD automatic upgrade
feature is enabled.
RP/0/RP0/CPU0:ios#show fpd package
Thu Jun 28 15:31:47.745 IST
=============================== ================================================
Field Programmable Device Package
================================================
Req SW Min Req Min Req
Card Type FPD Description Reload Ver SW Ver Board Ver
=================== ========================== ====== ======= ======== =========
--------------------------------------------------------------------------------
NCS1002 CDSP_PORT_05 NO 3.77 3.77 0.0
CDSP_PORT_06 NO 3.77 3.77 0.0
CDSP_PORT_12 NO 3.77 3.77 0.0
CDSP_PORT_13 NO 3.77 3.77 0.0
CDSP_PORT_19 NO 3.77 3.77 0.0
CDSP_PORT_20 NO 3.77 3.77 0.0
CDSP_PORT_26 NO 3.77 3.77 0.0
CDSP_PORT_27 NO 3.77 3.77 0.0
CFP2_PORT_05 NO 5.23 5.23 2.1
CFP2_PORT_05 NO 1.80 1.80 3.0
CFP2_PORT_05 NO 3.20 3.20 4.2
CFP2_PORT_06 NO 5.23 5.23 2.1
CFP2_PORT_06 NO 1.80 1.80 3.0
CFP2_PORT_06 NO 3.20 3.20 4.2
CFP2_PORT_12 NO 5.23 5.23 2.1
CFP2_PORT_12 NO 1.80 1.80 3.0
CFP2_PORT_12 NO 3.20 3.20 4.2
CFP2_PORT_13 NO 5.23 5.23 2.1
CFP2_PORT_13 NO 1.80 1.80 3.0
CFP2_PORT_13 NO 3.20 3.20 4.2
CFP2_PORT_19 NO 5.23 5.23 2.1
CFP2_PORT_19 NO 1.80 1.80 3.0
CFP2_PORT_19 NO 3.20 3.20 4.2
CFP2_PORT_20 NO 5.23 5.23 2.1
CFP2_PORT_20 NO 1.80 1.80 3.0
CFP2_PORT_20 NO 3.20 3.20 4.2
CFP2_PORT_26 NO 5.23 5.23 2.1
CFP2_PORT_26 NO 1.80 1.80 3.0
CFP2_PORT_26 NO 3.20 3.20 4.2
CFP2_PORT_27 NO 5.23 5.23 2.1
CFP2_PORT_27 NO 1.80 1.80 3.0
CFP2_PORT_27 NO 3.20 3.20 4.2
CTRL_BKP_UP(A) YES 2.23 2.23 0.1
CTRL_FPGA_UP(A) YES 2.23 2.23 0.1
CTRL_BKP_LOW(A) YES 2.23 2.23 0.1
CTRL_FPGA_LOW(A) YES 2.23 2.23 0.1
--------------------------------------------------------------------------------
NCS1002--RP BIOS_Backup(A) YES 14.00 14.00 0.1
BIOS_Primary(A) YES 14.00 14.00 0.1
Daisy_Duke_BKP(A) YES 0.15 0.15 0.1
Daisy_Duke_FPGA(A) YES 0.17 0.17 0.1
--------------------------------------------------------------------------------
NCS1K-2KW-AC PO-PriMCU(A) NO 4.00 4.00 0.0
PO-PriMCU(A) NO 4.00 4.00 0.0
--------------------------------------------------------------------------------
NCS1K-2KW-DC PO-PriMCU(A) NO 1.10 1.10 0.0
PO-PriMCU(A) NO 1.10 1.10 0.0
The following example shows the output of show fpd package command after the software upgrade is
complete.
System Setup and Software Installation Guide for Cisco NCS 1002
61
Perform System Upgrade and Install Feature Packages
FPD Automatic Upgrade

Cisco NCS 1002 Specifications

General

Brand	Cisco
Model	NCS 1002
Category	Network Hardware
Language	English