EasyManuals Logo

Cisco Telepresence MX800 Administrator's Guide

Cisco Telepresence MX800
141 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #101 background imageLoading...
Page #101 background image
D15119.02 MX700 and MX800 Administrator Guide TC7.2, AUGUST 2014. www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved.
101
Cisco TelePresence MX700 and MX800 Administrator Guide
SIP Profile [1..1] Outbound
Turn on or off the client initiated connections mechanism for firewall traversal, connection reuse
and redundancy. The current version supports RFC 5626.
Requires user role: ADMIN
Value space: <Off/On>
Off: Connect to the single proxy configured first in Proxy Address list.
On: Set up multiple outbound connections to servers in the Proxy Address list.
Example:
SIP Profile 1 Outbound: Off
SIP Profile [1..1] Proxy [1..4] Address
The Proxy Address is the manually configured address for the outbound proxy. It is possible to
use a fully qualified domain name, or an IP address. The default port is 5060 for TCP and UDP
but another one can be provided. If SIP Profile Outbound is enabled, multiple proxies can be
addressed.
Requires user role: ADMIN
Value space: <S: 0, 255>
Format: A valid IPv4 address, IPv6 address or DNS name.
Example:
SIP Profile 1 Proxy 1 Address: ""
SIP Profile [1..1] Proxy [1..4] Discovery
Select if the SIP Proxy address is to be obtained manually or by using Dynamic Host
Configuration Protocol (DHCP).
Requires user role: ADMIN
Value space: <Auto/Manual>
Auto: When Auto is selected, the SIP Proxy address is obtained using Dynamic Host
Configuration Protocol (DHCP).
Manual: When Manual is selected, the manually configured SIP Proxy address will be used.
Example:
SIP Profile 1 Proxy 1 Discovery: Manual
SIP Profile [1..1] Type
Enables SIP extensions and special behavior for a vendor or provider.
Requires user role: ADMIN
Value space: <Standard/Cisco>
Standard: Use this when registering to standard SIP Proxy (tested with Cisco TelePresence
VCS and Broadsoft)
Cisco: Use this when registering to Cisco Unified Communication Manager.
Example:
SIP Profile 1 Type: Standard
SIP Profile [1..1] Mailbox
When registered to a Cisco Unified Communications Manager (CUCM) you may be offered
the option of having a private voice mailbox. Enter the number (address) of the mailbox in this
setting, or leave the string empty if you do not have a voice mailbox.
Requires user role: ADMIN
Value space: <S: 0, 255>>
Format: String with a maximum of 255 characters.
Example:
SIP Profile 1 Mailbox: "12345678"
SIP Profile [1..1] Line
When registered to a Cisco Unified Communications Manager (CUCM) the endpoint may be
part of a shared line. This means that several devices share the same directory number. The
different devices sharing the same number receive status from the other appearances on the
line as defined in RFC 4235.
Note that shared lines are set up by CUCM, not by the endpoint. Therefore do not change this
setting manually; CUCM pushes this information to the endpoint when required.
Requires user role: ADMIN
Value space: <Private/Shared>
Shared: The system is part of a shared line and is therefore sharing its directory number with
other devices.
Private: This system is not part of a shared line (default).
Example:
SIP Profile 1 Line: Private
Contents
Introduction
Web interface
System settings
Setting passwords
Appendices
System settings

Table of Contents

Other manuals for Cisco Telepresence MX800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Cisco Telepresence MX800 and is the answer not in the manual?

Cisco Telepresence MX800 Specifications

General IconGeneral
Pan range-90 - 60 °
Product typeVideo conferencing service management system
Product colorWhite
Wall mountableYes
Tilt angle range-14 - 12 °
Number of persons- person(s)
Aspect ratio16:9
Maximum frame rate60 fps
Supported video modes720p, 1080p
Video formats supportedH.261, H.263, H.264, H.265
Resolution at capture speed1920x1080@60fps
Supported graphics resolutions352 x 288, 512 x 288, 1024 x 576 (WSVGA), 1024 x 768 (XGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Megapixel- MP
Sensor type-
Digital zoom2 x
Optical zoom10 x
Image sensor size- \
Closest focusing distance1 m
Ethernet LAN data rates10, 100, 1000 Mbit/s
Display diagonal70 \
Storage temperature (T-T)-20 - 60 °C
Operating temperature (T-T)0 - 40 °C
Operating relative humidity (H-H)10 - 90 %
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power consumption (max)591 W
Power consumption (typical)571 W

Related product manuals