Cisco Telepresence MX800 Administrator's Guide

D15119.02 MX700 and MX800 Administrator Guide TC7.2, AUGUST 2014. www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved.
63
Cisco TelePresence MX700 and MX800 Administrator Guide
Audio Input Microphone [1..8] Level
Define the audio level of the Microphone input connector, in steps of 1dB.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete
overview of the menu values represented in dB.
Requires user role: ADMIN
Value space: <0..70>
Range: Select a value between 0 and 70 dB.
Example:
Audio Input Microphone 1 Level: 58
Audio Input Microphone [1..8] Mode
Set the audio input microphone mode.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the microphone connector.
On: Enable the microphone connector.
Example:
Audio Input Microphone 1 Mode: On
Audio Input Microphone [1..8] Type
The microphone connectors are intended for electret type microphones. The microphone
connector can be set to line or microphone mode.
Requires user role: ADMIN
Value space: <Microphone/Line>
Microphone: Select Microphone when you have 48 V Phantom voltage and the pre-
amplification is On.
Line: Select Line when you have a standard balanced line input. The phantom voltage and
pre-amplification is Off.
Example:
Audio Input Microphone 1 Type: Line
Audio Output HDMI [2] Level
This setting only applies to MX800.
Define the output level of the HDMI output connector, in steps of 1 dB.
See the Audio Level tables in the Physical Interfaces Guide for the codec for a complete
overview of the menu values represented in dB.
Requires user role: ADMIN
Value space: <-24..0>
Range: Select a value from -24 to 0 dB.
Example:
Audio Output HDMI 2 Level: 0
Audio Output HDMI [2] Mode
This setting only applies to MX800.
Determine if the audio channel on the HDMI output connector shall be enabled.
Requires user role: ADMIN
Value space: <Off/On>
Off: Disable the audio channel on the HDMI output.
On: Enable the audio channel on the HDMI output.
Example:
Audio Output HDMI 2 Mode: Off
Audio Output Line [1..6] Channel
Define whether the Audio Line output is a mono signal or part of a multichannel signal.
Requires user role: ADMIN
Value space: <Right/Left/Mono>
Right: The Audio Line output signal is the right channel of a stereo signal.
Left: The Audio Line output signal is the left channel of a stereo signal.
Mono: The Audio Line output signal is a mono signal.
Example:
Audio Output Line 1 Channel: left
Contents
Introduction
Web interface
System settings
Setting passwords
Appendices
System settings

Cisco Telepresence MX800 Specifications

General

Pan range	-90 - 60 °
Product type	Video conferencing service management system
Product color	White
Wall mountable	Yes
Tilt angle range	-14 - 12 °
Number of persons	- person(s)
Aspect ratio	16:9
Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.263, H.264, H.265
Resolution at capture speed	1920x1080@60fps
Supported graphics resolutions	352 x 288, 512 x 288, 1024 x 576 (WSVGA), 1024 x 768 (XGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Megapixel	- MP
Sensor type	-
Digital zoom	2 x
Optical zoom	10 x
Image sensor size	- \
Closest focusing distance	1 m
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Display diagonal	70 \
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	591 W
Power consumption (typical)	571 W