Cisco Telepresence MX800 Administrator's Guide

D15119.02 MX700 and MX800 Administrator Guide TC7.2, AUGUST 2014. www.cisco.com — Copyright © 2014 Cisco Systems, Inc. All rights reserved.
89
Cisco TelePresence MX700 and MX800 Administrator Guide
NetworkServices SNMP SystemContact
Enter the name of the Network Services SNMP System Contact.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example:
NetworkServices SNMP SystemContact: ""
NetworkServices SNMP SystemLocation
Enter the name of the Network Services SNMP System Location.
Requires user role: ADMIN
Value space: <S: 0, 50>
Format: String with a maximum of 50 characters.
Example:
NetworkServices SNMP SystemLocation: ""
NetworkServices SSH Mode
SSH (or Secure Shell) protocol can provide secure encrypted communication between the
codec and your local computer.
Requires user role: ADMIN
Value space: <Off/On>
Off: The SSH protocol is disabled.
On: The SSH protocol is enabled.
Example:
NetworkServices SSH Mode: On
NetworkServices SSH AllowPublicKey
Secure Shell (SSH) public key authentication can be used to access the codec.
Requires user role: ADMIN
Value space: <Off/On>
Off: The SSH public key is not allowed.
On: The SSH public key is allowed.
Example:
NetworkServices SSH AllowPublicKey: On
NetworkServices CTMS Mode
This setting determines whether or not to allow multiparty conferences controlled by a Cisco
TelePresence Multipoint Switch (CTMS).
Video systems are able to initiate or join non-encrypted multiparty conferences controlled by
CTMS version 1.8 or later. Encrypted conferences are supported as from software versions
CTMS 1.9.1. Encryption is addressed in the NetworkServices CTMS Encryption setting.
Requires user role: ADMIN
Value space: <Off/On>
Off: Multiparty conferencing via CTMS is prohibited.
On: Multiparty conferencing via CTMS is allowed.
Example:
NetworkServices CTMS Mode: On
NetworkServices CTMS Encryption
This setting indicates whether or not the video system supports encryption when participating
in a multiparty meeting controlled by a Cisco TelePresence Multipoint Switch (CTMS).
CTMS allows three security settings for meetings: non-secure (not encrypted), best effort
(encrypted if all participants support encryption, otherwise not encrypted) and secure (always
encrypted).
Requires user role: ADMIN
Value space: <Off/BestEffort>
Off: The video system does not allow encryption and therefore cannot participate in a secure
CTMS meeting (encrypted). When participating in a best effort CTMS meeting, the meeting
will be downgraded to non-secure (not encrypted).
BestEffort: The video system can negotiate encryption parameters with CTMS and
participate in a secure CTMS meeting (encrypted). Do not use this value if the CTMS version
is older than 1.9.1.
Example:
NetworkServices CTMS Encryption: Off
Contents
Introduction
Web interface
System settings
Setting passwords
Appendices
System settings

Cisco Telepresence MX800 Specifications

General

Pan range	-90 - 60 °
Product type	Video conferencing service management system
Product color	White
Wall mountable	Yes
Tilt angle range	-14 - 12 °
Number of persons	- person(s)
Aspect ratio	16:9
Maximum frame rate	60 fps
Supported video modes	720p, 1080p
Video formats supported	H.261, H.263, H.264, H.265
Resolution at capture speed	1920x1080@60fps
Supported graphics resolutions	352 x 288, 512 x 288, 1024 x 576 (WSVGA), 1024 x 768 (XGA), 1280 x 720 (HD 720), 1280 x 768 (WXGA), 1920 x 1080 (HD 1080), 1920 x 1200 (WUXGA)
Megapixel	- MP
Sensor type	-
Digital zoom	2 x
Optical zoom	10 x
Image sensor size	- \
Closest focusing distance	1 m
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Display diagonal	70 \
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
AC input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	591 W
Power consumption (typical)	571 W