SRT X-BAND RADAR SYSTEMS
INDEX
304202P003 ii Rev. C
3.2.1.7 SYSTEM MONITOR FUNCTIONS.........................................................................................3.10
3.2.1.8 PERFORMANCE MONITOR FUNCTIONS..............................................................................3.10
3.2.1.9 INPUT AND OUTPUT INTERFACE........................................................................................3.11
3.2.1.10 AZIMUTH (AZ) AND HEADING LINE (HL) SIGNAL CIRCUIT GENERATOR.........................3.11
3.2.2 RF HEAD.............................................................................................................................3.11
3.2.3 BRUSHLESS MOTOR CONTROLLER........................................................................................3.12
3.2.4 MOTOR UNIT.........................................................................................................................3.13
3.2.5 OPTIONAL EQUIPMENT: SRT ADAPTER BOX.........................................................................3.14
3.2.6 OPTIONAL EQUIPMENT: HEATERS ........................................................................................3.14
3.2.7 OPTIONAL EQUIPMENT: ENCODER........................................................................................3.14
CHAPTER 4 PREVENTIVE MAINTENANCE..................................................................................4.1
4.1 INTRODUCTION........................................................................................................................4.1
4.2 PREVENTIVE MAINTENANCE PROCEDURE...............................................................................4.1
CHAPTER 5 TROUBLESHOOTING..................................................................................................5.1
5.1 INTRODUCTION........................................................................................................................5.1
5.1.1 GENERAL ................................................................................................................................5.1
5.1.2 ORGANIZATION .......................................................................................................................5.1
5.1.3 PERSONNEL.............................................................................................................................5.1
5.1.4 TOOLS AND INSTRUMENTS ......................................................................................................5.1
5.2 TROUBLESHHOTING PROCEDURES...........................................................................................5.2
5.2.1 SAFETY PRECAUTIONS ............................................................................................................5.2
5.2.2 TROUBLESHOOTING OPERATIONS ...........................................................................................5.2
CHAPTER 6 CORRECTIVE MAINTENANCE.................................................................................6.1
6.1 GENERAL ................................................................................................................................6.1
6.1.1 INTRODUCTION........................................................................................................................6.1
6.1.2 SAFETY PRECAUTIONS ............................................................................................................6.1
6.1.3 PERSONNEL.............................................................................................................................6.1
6.1.4 REQUIRED TOOLS AND INSTRUMENTS.....................................................................................6.1
6.2 CORRECTIVE MAINTENANCE PROCEDURES.............................................................................6.2
6.2.1 GENERAL ................................................................................................................................6.2
6.2.2 ANTENNA REPLACEMENT .......................................................................................................6.2
6.2.3 OPENING/CLOSING OF THE TXRX COVER ..............................................................................6.3
6.2.4 REPLACEMENT OF THE MOTOREDUCER ASSY .........................................................................6.3
6.2.5 REPLACEMENT OF THE BRUSHLESS MOTOR CONTROLLER......................................................6.4
6.2.6 REPLACEMENT OF THE MAGNETRON.......................................................................................6.4
6.2.7 REPLACEMENT OF THE RF FRONT END ASSY..........................................................................6.5
6.2.8 REMOVAL/INSTALLATION OF THE ELECTRONICS ASSY ...........................................................6.6
6.2.9 REPLACEMENT OF THE BEARING READER BOARD...................................................................6.7
CHAPTER 7 PART LIST ......................................................................................................................7.1
7.1 INTRODUCTION........................................................................................................................7.1
7.1.1 PART LIST ...............................................................................................................................7.1
7.1.2 PART LOCATION ILLUSTRATION..............................................................................................7.1
7.2 PART LIST TABLES..................................................................................................................7.2
CHAPTER 8 INSTALLATION.............................................................................................................8.1
8.1 INTRODUCTION........................................................................................................................8.2
8.1.1 SHIPPING.................................................................................................................................8.2
8.1.2 UNPACKING ............................................................................................................................8.2
8.1.3 STORAGE.................................................................................................................................8.3
8.1.4 HANDLING ..............................................................................................................................8.3
8.2 SPECIFICATIONS ......................................................................................................................8.3
8.2.1 DIMENSIONS AND WEIGHTS (ALSO SEE OUTLINE DRAWINGS) ................................................8.3
8.2.2 REQUIRED POWER ...................................................................................................................8.4
8.2.3 ENVIRONMENTAL DATA..........................................................................................................8.4
8.3 INSTALLATION ........................................................................................................................8.5
8.3.1 INSTALLATION PRINCIPLES .....................................................................................................8.5
8.3.2 MECHANICAL INSTALLATION ..................................................................................................8.7
8.3.2.1 UNIT (PEDESTAL + TRANSCEIVER)......................................................................................8.7
To Next Page
Loading...