5 — MONITOR MENU
Curtis 1239E-1269E Manual, os 37.0 RevA – May 2021
Return to TOC
pg. 84
Monitor Menu: VEHICLE
VARIABLE DISPLAY RANGE DESCRIPTION
Vehicle Speed
Vehicle_Speed
0x320A 0x00
–3276.8 – 3276.7
–32768 – 32767
Vehicle speed, in units of MPH or KPH, depending on the setting of the Metric
Units parameter (see Program » Vehicle menu).
For accurate speed estimates, the Speed to RPM parameter must be set correctly.
Vehicle Odometer
Vehicle_Odometer
0x3200 0x00
0.0 – 10000000.0
0 – 100000000
Vehicle distance traveled, in units of miles or km, depending on the setting of
the Metric Units parameter in the Vehicle parameters menu.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
Vehicle Acceleration
Vehicle_Acceleration
0x35C1 0x00
0.000 – 10.000 g
0 – 10000
Vehicle acceleration. This is a calculated value. The Speed to RPM parameter
must be set correctly for an accurate measurement.
Time to Speed 1
Time_to_Capture_Speed_1
0x35BF 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to go from zero rpm to the programmed Capture
Speed 1 during its most recent such acceleration.
Time to Speed 2
Time_to_Capture_Speed_2
0x35BB 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to go from zero rpm to the programmed Capture
Speed 2 during its most recent such acceleration.
Time Between Speeds
Time_Between_Capture_ Speeds
0x35C4 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to go from programmed Capture Speed 1 to
programmed Capture Speed 2 during its most recent such acceleration.
Time to Dist 1
Time_to_Capture_Distance_1
0x3612 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to travel from zero rpm to the programmed Capture
Distance 1 during its most recent such trip.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
Time to Dist 2
Time_to_Capture_Distance_2
0x3613 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to travel from zero rpm to the programmed Capture
Distance 2 during its most recent such trip.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
Time to Dist 3
Time_to_Capture_Distance_3
0x3614 0x00
0.00 – 128.00 s
0 – 32000
Time taken for the vehicle to travel from zero rpm to the programmed Capture
Distance 3 during its most recent such trip.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
Braking Distance Captured
Braking_Distance_Captured
0x3201 0x00
0.0 – 1000000.0
0 – 40000000
Distance traveled by the vehicle starting with vehicle braking (initiated by
throttle reversal, brake pot, VCL_Brake, or interlock braking) and ending when
Motor_RPM = 0. Units are meters or feet, depending on the setting of the
Metric Units parameter.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
Distance Since Stop
Distance_Since_Stop
0x324E 0x00
0.0 – 1000000.0
0 – 40000000
Distance traveled by the vehicle starting from a stop. In effect, the vehicle is
used as a tape measure. (In other words, if the vehicle travels 300 feet forward
and then 300 feet in reverse, the distance would be 600.) The distance is
continuously updated and will stop (and restart) when Motor_RPM = 0.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly. Units are meters or feet, depending on the setting of the Metric
Units parameter.
Distance Fine
Distance_Fine_Long
0x3616 0x00
–214748364.8 – 214748364.7
–2147483648 – 2147483647
Position measurement. Net distance in both the forward and reverse
directions. (In other words, if the vehicle travels 20 inches forward and then
20 inches in reverse, the distance would be zero.) The distance is continuously
updated and will roll over when the variable goes over the limits. Units are
decimeters or inches, depending on the setting of the Metric Units parameter.
For accurate distance measurements, the Speed to RPM parameter must be
set correctly.
NOTE: All vehicle calculations assume no tire slippage.
Quick Links:
Vehicle Menu parameters p.72
Metric Units
Speed to RPM
Capture Speed 1, 2
Capture Distance 1, 2, 3
To Next Page
Loading...
