Danfoss VLT AutomationDrive FC 300

Term. X48/4 Filter Time Constant 35-14 230
Term. X48/4 High Temp. Limit 35-17 230
Term. X48/4 Input Type 35-01 229
Term. X48/4 Low Temp. Limit 35-16 230
Term. X48/4 Temp. Monitor 35-15 230
Term. X48/4 Temp. Unit 35-00 229
Term. X48/7 Filter Time Constant 35-24 230
Term. X48/7 High Temp. Limit 35-27 231
Term. X48/7 Input Type 35-03 229
Term. X48/7 Low Temp. Limit 35-26 231
Term. X48/7 Temp. Monitor 35-25 230
Term. X48/7 Temp. Unit 35-02 229
Terminal 27 Mode 5-01 92
Terminal 27 Pulse Output Variable 5-60 111
Terminal 29 Mode 5-02 92
Terminal 29 Pulse Output Variable 5-63 112
Terminal 37 Safe Stop 5-19 98
Terminal 42 Output 6-50 120
Terminal 42 Output Bus Control 6-53 122
Terminal 42 Output Filter 6-55 122
Terminal 42 Output Max Scale 6-52 121
Terminal 42 Output Min Scale 6-51 121
Terminal 42 Output Timeout Preset 6-54 122
Terminal 53 Filter Time Constant 6-16 118
Terminal 53 High Current 6-13 117
Terminal 53 High Ref./feedb. Value 6-15 117
Terminal 53 High Voltage 6-11 117
Terminal 53 Low Current 6-12 117
Terminal 53 Low Ref./feedb. Value 6-14 117
Terminal 53 Low Voltage 6-10 117
Terminal 53 Switch Setting 16-61 217
Terminal 54 Filter Time Constant 6-26 118
Terminal 54 High Current 6-23 118
Terminal 54 High Ref./feedb. Value 6-25 118
Terminal 54 High Voltage 6-21 118
Terminal 54 Low Current 6-22 118
Terminal 54 Low Ref./feedb. Value 6-24 118
Terminal 54 Low Voltage 6-20 118
Terminal 54 Switch Setting 16-63 217
Terminal X30/11 High Voltage 6-31 119
Terminal X30/11 Low Voltage 6-30 119
Terminal X30/12 High Voltage 6-41 119
Terminal X30/12 Low Voltage 6-40 119
Terminal X30/6 Pulse Output Variable 5-66 112
Terminal X30/8 Bus Control 6-63 124
Terminal X30/8 Max. Scale 6-62 124
Terminal X30/8 Min. Scale 6-61 124
Terminal X30/8 Output 6-60 122
Terminal X30/8 Output Timeout Preset 6-64 124
Terminal X45/1 Output Min Scale, 6-71 125
Terminal X45/3 Output Min Scale, 6-81 126
Thermal Load 52, 213
Thermistor 59
Thermistor 8
Thermistor Source 1-93 62
This Set-up Linked To 0-12 33
[Torque %] 16-22 214
[Torque %] High Res. 16-21 214
Torque Characteristics 1-03 46
Torque Limit Factor Source 4-20 87
Torque Limit Generator Mode 4-17 86
Torque Limit Motor Mode 4-16 86
[Torque Nm] 16-16 213
[Torque Nm] High 16-25 214
Torque Pi Integration Time 7-13 131
Torque Pi Proportional Gain 7-12 130
Torque Ramp Time 2-27 70
Torque Ref 2-26 70
Index FC 300 Programming Guide
274 MG.33.M8.02 - VLT
®
is a registered Danfoss trademark