Danfoss VLT FC 302 User Manual

6.3.11 9-** Profibus
Par. No. # Parameter description Default value 4-set-up FC 302
only
Change
during
operation
Conver-
sion index
Type
9-00 Setpoint 0 N/A All set-ups TRUE 0 Uint16
9-07 Actual value 0 N/A All set-ups FALSE 0 Uint16
9-15 PCD write configuration App.Dependent 1 set-up TRUE - Uint16
9-16 PCD read configuration App.Dependent 2 set-ups TRUE - Uint16
9-18 Node address 126 N/A 1 set-up TRUE 0 Uint8
9-22 Telegram selection [100] none 1 set-up TRUE - Uint8
9-23 Parameters for signals 0 All set-ups TRUE - Uint16
9-27 Parameter edit [1] enabled 2 set-ups FALSE - Uint16
9-28 Process control [1] Enable cyclic master 2 set-ups FALSE - Uint8
9-44 Fault message counter 0 N/A All set-ups TRUE 0 Uint16
9-45 Fault code 0 N/A All set-ups TRUE 0 Uint16
9-47 Fault number 0 N/A All set-ups TRUE 0 Uint16
9-52 Fault situation counter 0 N/A All set-ups TRUE 0 Uint16
9-53 Profibus warning word 0 N/A All set-ups TRUE 0 V2
9-63 Actual baud rate
[255] No baudrate
found All set-ups TRUE - Uint8
9-64 Device identification 0 N/A All set-ups TRUE 0 Uint16
9-65 Profile number 0 N/A All set-ups TRUE 0 OctStr[2]
9-67 Control word 1 0 N/A All set-ups TRUE 0 V2
9-68 Status word 1 0 N/A All set-ups TRUE 0 V2
9-71 Profibus save data values [0] Off All set-ups TRUE - Uint8
9-72 ProfibusDriveReset [0] No action 1 set-up FALSE - Uint8
9-75 DO identification 0 N/A All set-ups TRUE 0 Uint16
9-80 Defined parameters (1) 0 N/A All set-ups FALSE 0 Uint16
9-81 Defined parameters (2) 0 N/A All set-ups FALSE 0 Uint16
9-82 Defined parameters (3) 0 N/A All set-ups FALSE 0 Uint16
9-83 Defined parameters (4) 0 N/A All set-ups FALSE 0 Uint16
9-84 Defined parameters (5) 0 N/A All set-ups FALSE 0 Uint16
9-90 Changed parameters (1) 0 N/A All set-ups FALSE 0 Uint16
9-91 Changed parameters (2) 0 N/A All set-ups FALSE 0 Uint16
9-92 Changed parameters (3) 0 N/A All set-ups FALSE 0 Uint16
9-93 Changed parameters (4) 0 N/A All set-ups FALSE 0 Uint16
9-94 Changed parameters (5) 0 N/A All set-ups FALSE 0 Uint16
9-99 Profibus revision counter 0 N/A All set-ups TRUE 0 Uint16
Programming Operating Instructions
MG37A202 Danfoss A/S © Rev. 2014-07-29 All rights reserved. 87
6 6

Danfoss VLT FC 302 Specifications

General

Brake Function	Built-in brake chopper in all units up to 22 kW
Output Voltage Range	0-100% of input voltage
Power Range	0.37 kW
Control Modes	VVCplus, Flux, U/f
Protection Features	Overvoltage, undervoltage, overcurrent, short circuit, overtemperature, overload
Communication Options	Modbus RTU, BACnet, Ethernet/IP, Profinet, Profibus, CANopen, DeviceNet
Ambient Temperature Range	-10°C to +50°C (derating above +40°C)
Enclosure Rating	IP20, IP21, IP55
Cooling Method	Air-cooled
Input Voltage	200-240V, 380-480V, 525-600V