What to do if I get an error message that the USB is not detected on my DataCard Printer?
If you receive an error message stating that the USB is not detected, it means the USB installer timed out before a printer was detected. Remove the Card Printer Driver from the Device Manager before reinstalling the printer.
How to fix a loose cable on DataCard Printer?
To resolve a loose cable issue with your DataCard Printer, reconnect the USB cable to both the PC and the printer ports. Then, power the printer off and back on. If the PC and printer still don't communicate, restart your PC.
What to do if a print job disappears from the DataCard Printer queue?
If a print job disappears from the queue of your DataCard Printer without printing, it may be due to the USB cable being disconnected after the job was sent. Reconnect the cable and try the job again.
What to do if the data cable is damaged on DataCard CR805?
If the data cable of your DataCard Printer is damaged or frayed, power off the printer. If you have a spare cable, replace the damaged one. Otherwise, contact your service provider to order a new data cable.
Why PC USB port does not communicate with DataCard CR805?
If the PC USB port isn't communicating with the DataCard Printer USB port, it might be due to power management settings on your PC shutting down USB communication. To fix this, open Device Manager and go to the list of USB devices. Disable the shutdown option for each hub in the list. Restart your PC for the changes to take effect. If you are using a laptop, allow a few moments after hibernation for USB communication to be enabled. You can also try unplugging and reconnecting the USB printer port. If the problem persists, consider replacing the PC port or the PC. Contact your PC or port vendor for further assistance if needed.
What to do if DataCard CR805 does not install or print when connected to a remote network via VPN?
If your DataCard Printer doesn't install or print while your PC is connected to a remote network using VPN Client software, you can either configure your VPN software to allow local network connections or disconnect the VPN Client software from the network.
How do I reset the counters on my DataCard CR805 Printer?
To reset the counters, click 'Run'.
How do I reset the Activity Log on my DataCard Printer?
To reset the Activity Log, click 'Run'.
What to do if card is not in the laminator of DataCard CR805?
If the card is not where it should be in the laminator of your DataCard Printer, open the laminator and remove the L1 supply cartridge. Turn the knob to remove the card, then replace the supply cartridge and close the laminator.
How to fix opaque areas on DataCard CR805?
If the patch shows opaque areas at the leading edge of the card when using your DataCard Printer, decrease the laminator temperature setting. If the problem continues, contact your service provider for assistance.
Lists the Windows operating systems supported by the Card Printer Driver.
Lists the Datacard and Entrust Datacard printers supported by the driver.
Provides an overview of the tasks performed by the Card Printer Driver after installation.
Explains how the printer and driver communicate via USB or network connections.
Step-by-step instructions for installing the driver via USB or network.
Process for updating an existing Card Printer Driver installation.
Procedure for updating the Card Printer Driver to the latest version.
Guidance on updating the driver on client PCs in a shared printer setup.
Options for connecting multiple printers to a single PC.
Guidelines for installing multiple printers using USB cables.
Enables secure, encrypted transmission of print commands and card data.
Step-by-step guide to configuring secure printing via Printer Manager.
Enables sharing a printer over a network using Microsoft File and Printer Sharing.
Enables printing to a group of printers acting as one.
Step-by-step instructions for configuring printer pooling.
Allows viewing printer settings and defining printer communication with the PC.
Displays printer status, port type, IP address, and printer information.
Procedures for removing the Card Printer Driver from the PC.
Specifies default settings for card printing via Printing Preferences.
Allows sending a card through the printer without printing on it.
Applies an additional layer of retransfer film for durability.
Specifies printing and non-printing areas on the card.
Selects preset masks for CR805 retransfer printers.
Ensures printer, manager, and driver are set up for rewritable printing.
Supports color print ribbons with a UV fluorescent panel for security.
Formatted text converted to printer commands for operations.
Methods to prevent printing and topcoat on specific card areas.
Blocks primer on smart card chips and applies inhibitor to magnetic stripes.
Formats magnetic stripe data when application cannot.
Applies a second layer of retransfer film for added durability.
Specifies font and position for embossed/indented data.
Provides fonts to format magnetic stripe data when escapes are not used.
Addresses common issues preventing successful driver installation.
Solves problems related to installing the driver via USB connection.
Solves problems related to installing the driver over a network connection.
Configures the host PC for printer sharing on Server OS.
Installs the driver on client PCs for Server OS sharing.
To Next Page
General
