ENGLISH
24
NOTES:
• The system setup function cannot be used when the
PURE DIRECT mode is set or the “VIDEO OFF”
setting is selected. To use the system setup
function, cancel the PURE DIRECT mode or select
the “VIDEO ON” setting.
• The multi-room video output is not output in the
PURE DIRECT and VIDEO OFF mode.
• The channel level and surround parameters in the
PURE DIRECT mode are the same as in the DIRECT
mode.
• When the PURE DIRECT button is pressed while in
the PURE DIRECT mode, the PURE DIRECT mode is
canceled and the DIRECT mode is set.
4
VIDEO ON/OFF button
When no video signals of a DVD, etc., are
connected to the AVC-A1SR and DVD, etc., are
connected directly to a TV, etc., the unneeded
video circuitry can be turned off by selecting
the “VIDEO OFF” setting.
[1] Multi-zone playback using the MULTI ZONE1 terminals
The AVC-A1SR is equipped with audio pre-out terminals for which the volume is adjustable (M-ZONE1) and
composite video output terminals as the MULTI ZONE1 output terminals.
A separately sold stereo power amplifier can be connected to enjoy multi-zone playback.
NOTE:
The multi-room video output is not output in the PURE DIRECT and VIDEO OFF modes.
MULTI ROOM MUSIC ENTERTAINMENT SYSTEM
• When the outputs of the MULTI ZONE AUDIO OUT terminals are wired and connected to integrated amplifiers
installed in other rooms, different sources can be played in rooms other than the main room in which this unit
and the playback devices are installed. (Refer to ANOTHER ROOM on the diagram below.)
To control playback devices other than the ones above, either use that device’s remote control unit or preset
a separately sold programmable remote control unit.
Multi-source and multi-zone playback
NOTE:
• For the AUDIO output, use high quality pin-plug cords and wire in such a way that there is no humming
or noise.
• When the input mode is set to EXT.IN (1 or 2), playback in the DIRECT, STEREO, DOLBY/DTS SURROUND,
HOME THX CINEMA, WIDE SCREEN, 5CH/7CH STEREO and DSP SIMULATION modes is only possible when
DSP MODE is selected for Ext.In Setup at System Setup.
•
When the “INPUT CH” parameter is set to “MULTI CH”, the “MULTI CH DIRECT” mode is set when the DIRECT button
is pressed, and the “MULTI CH IN” mode is set when the DOLBY DTS/SURROUND button is pressed. (See pages 33, 34.)
NOTES:
• In play modes other than the external input mode, the signals connected to these jacks cannot be played.
In addition, signals cannot be output from channels not connected to the input jacks.
• The external input mode can be set for any input source. To watch video while listening to sound, select
the input source to which the video signal is connected, then set this mode.
The AVC-A1SR is equipped with three 2-channel playback modes exclusively for music.
Select the mode to suit your tastes.
Playing audio sources (CDs and DVDs)
1
PURE DIRECT mode
In this mode, the music is played with an
extremely high level of sound quality.
When this mode is set, all the video-related
circuits are turned off so that music signals can
be reproduced with high quality. When an
analog input mode or EXT. IN mode is selected,
the digital processing circuitry is also turned off
to achieve analog sound with even higher
purity.
(Main unit) (Remote control unit)
2 Playback using the DENON Link connector
Digital transfer and multi-channel playback of DVD audio discs and other multi-channel sources is possible by
connecting the AVC-A1SR to a Denon DVD player equipped with a Denon Link connector using the
connection cable included with the DVD player.
With discs on which special copyright protection measures have been taken, however, the digital signals may
not be output from the DVD player. In this case, connect the DVD player’s analog multi-channel output to the
AVC-A1SR’s EXT.IN-1 or EXT.IN-2 terminals for playback.
Also refer to your DVD player’s operating instructions.
To Next Page
Loading...
