R
L
R
L
R
L
SURR.-B
L
S-VIDEO
OUT
OUT OUT
IN
IN
IN
EXT. IN-1
SW
12
EXT. IN
(REMOTE CONTROL)
ROOM TO ROOM
DENON
LINK
POWER AMP
RS-232C
TRIGGER OUT
DC 12V 20mA MAX.
OPTICAL
DIGITAL
345
12345656
EXT. IN-2 PRE OUT OUT
PREOUT
OUT
OUT
IN OUT
AUDIO
IN
VDP TV
DBS /
V. AUX VCR-1 VCR-2 VCR-3 VCR-1 VCR-2 VCR-3
SAT
MD /
AC IN
TAPE-2
CDR /
TAPE-1
MD /
MULTI ZONE
TAPE-2 1 2
CDR /
TAPE-1
DVD
CENTER SURR.
SURR.
BACK
SURR.
BACK
SURR.
BACK
FRONT CENTER SURR.FRONT
GITAL RF
CENTER SURR.FRONT
CD
COAXIAL
CONTROL OUT
OUT
IN
SW SW
TUNER
SPEAKER SYSTEMS
SPEAKER IMPEDANCE
FRONT, CENTER, SURROUND BACK
SURROUND A OR B / 6 16Ω
A + B / 8 16Ω
/ 6 16Ω
AC OUTLETS
SWITCHED 100W MAX.
AC 230V 50Hz
SB
MULTI
L
Power amplifier (Option)
REMOTE
(ON-OFF)
When connected as shown on the diagram below using connection cords included with Denon power
amplifiers, the power amplifier’s power can be turned on and off using the “M-ZONE1 ON/OFF” button on
the remote control unit.
AVC-A1SR
ANOTHER ROOM MAIN ROOM
B
RC-871
[2] Multi-zone playback using the MULTI ZONE2 terminals
The AVC-A1SR is equipped with audio pre output terminals with a fixed output level (M-ZONE2) as the
MULTI ZONE2 output terminals. (These are not video outputs.)
Settings can be made at the system setup menu so that the same source as the M-ZONE2 pre-out terminals
can be played from the speakers connected to the M-ZONE2 speaker terminals.
2 When using the PRE OUT terminals
NOTE:
When the main unit is set to the recording output mode, the M-ZONE2 remote control unit key cannot be
operated. (See page 22.)
2 When using the M-ZONE2 (MULTI) speaker terminals
AVC-A1SR
ANOTHER ROOM MAIN ROOM
RC-871
10
SURROUND
Before playing with the surround function
• Before playing with the surround function, be sure to use the test tones to adjust the playback level from the
different speakers. This adjustment can be performed with the system setup (see page 13) or from the remote
control unit, as described below.
• Adjusting with the remote control unit using the test tones is only possible in the “Auto” mode and only
effective in the DOLBY SURROUND and HOME THX CINEMA modes. The adjusted levels for the different
modes are automatically stored in the memory.
1
Press the TEST TONE button.
2
Test tones are output from the different
speakers. Press the CURSOR/PAGE button to
highlight the display, then use the jog stick to
adjust the channel level.
3
After completing the adjustment, press the
CURSOR/PAGE button again so that the display
is no longer highlighted, then press the TEST
TONE button to complete the operation.
• After adjusting using the test tones, make the desired settings for each surround mode to be played, then use
the procedure described below to adjust the levels of the various channels.
SURR.
PARAMETER
TONE
CONTROL
CH. VOL.
1
MAIN UNIT:
Press the MODE SELECT button
and select “CH VOL”.
The setting mode switches in the
following order each time the
button is pressed:
(Main unit)
REMOTE CONTROL UNIT:
Press the CH. SELECT button on
the “SURROUND 2/5” page.
“CH VOL” is selected.
(Remote control unit)
2
MAIN UNIT:
Use the FUNCTION knob to
select the speaker whose
level is to be adjusted.
REMOTE CONTROL UNIT:
Press the CURSOR/PAGE button on the
“SURROUND 2/5” page to highlight the
display, then press jog stick “ENTER”. The
channel (speaker) switches as shown on the
diagram below each time it is pressed.
FL C FR SR SBR SBL
SLSW
FADER
(Remote control unit)
INTEGRATED
AMPLIFIER
To Next Page
Loading...
