ENGLISH
34
2 Differences in surround mode names depending on the input signals
Input signals
PURE DIRECT, DIRECT
STEREO
HOME THX CINEMA
DTS SURROUND
DTS NEO:6
DOLBY DIGITAL
DOLBY PRO LOGIC
II
DSP SIMULATION
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC II
C
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC II
C
C
C
✳THX MTRX6.1
THX Ultra2 Cinema
THX MUSIC MODE
THX5.1
✳DTS ES MTRX
DTS SURROUND
E
E
E
C
C
C
✳THX MTRX6.1
THX Ultra2 Cinema
THX MUSIC MODE
THX5.1
✳DTS ES MTRX
DTS 96/24
E
E
E
C
C
C
B THX DSCRT6.1
THX MTRX6.1
B
DTS ES DSCRT6.
1
DTS MTRX6.1
E
E
E
C
C
C
THX
E
DTS NEO:6
E
DOLBY
PRO LOGIC II
C
C
C
✳
THX SURROUND EX
THX Ultra2 Cinema
THX MUSIC MODE
THX5.1
E
E
✳
DOLBY DIGITAL EX
DOLBY DIGITAL
E
C
ANALOG LINEAR PCM DTS (5.1 ch)
DTS 96/24(5.1 ch)
DTS (6.1 ch) D. D. (2 ch) D. D. (5.1 ch)
DTS DOLBY DIGITALSurround Mode
C : Selectable
✳ : The surround mode name differs depending on the “MODE/SB CH OUT” surround parameter setting.
B : The surround mode name differs depending on the input signal.
E : Not selectable
NOTES:
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the
button settings are reset to the default values
(the values set upon shipment from the factory).
12
LAST FUNCTION MEMORY
• This unit is equipped with a last function memory which stores the input and output setting conditions as they
were immediately before the power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function provides approximately one week of memory
storage when the main unit’s power switch is off and with the power cord disconnected.
13
INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable
result, the initialization of the microprocessor is required by the following procedure.
1
Switch off the unit using the main unit’s power
switch.
2
Press and hold the DIRECT buttons and
STEREO buttons at the same time, and turn the
main unit’s power switch on.
3
Check that the entire display is flashing with an
interval of about 1 second, and release your
fingers from the 2 buttons and the
microprocessor will be initialized.
Turning on the main unit’s power from the standby mode without using the remote control unit
• Press the power switch on the main unit while pressing the HOME THX CINEMA button on the main unit’s
panel to turn on the power.
Parameter (default values are shown in parentheses)
SURROUND PARAMETER
MODE
CINEMA
EQ
TONE
CONTROL
ROOM
SIZE
EFFECT
LEVEL
CENTER
WIDTH
PRO LOGIC II MUSIC MODE ONLY
DELAY
TIME
PANORAMA DIMENSION
E
E
E
E
E
E
C
(OFF)
E
E
E
E
E
E
E
E
E
E
PURE DIRECT, DIRECT
MULTI CH DIRECT
STEREO
MULTI CH IN
WIDE SCREEN
HOME THX CINEMA
DOLBY PRO LOGIC
II
DOLBY DIGITAL
DTS SURROUND
DTS NEO:6
5CH/7CH STEREO
SUPER STADIUM
ROCK ARENA
JAZZ CLUB
CLASSIC CONCERT
MONO MOVIE
MATRIX
E
E
C
(0dB)
C (0dB)
C (0dB)
E
C
(0dB)
C (0dB)
C (0dB)
C (0dB)
C (0dB)
C (Note 1)
C (Note 2)
C (0dB)
C (0dB)
C (0dB)
C (0dB)
E
E
E
C
(OFF)
E
C
(OFF)
C (OFF)
C (OFF)
C (OFF)
E
E
E
E
E
E
E
E
E
E
E
E
C
(CINEMA)
C
(CINEMA)
E
E
C
(CINEMA)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C
(Medium)
C
(Medium)
C
(Medium)
C
(Medium)
C
(Medium)
E
E
E
E
E
C
(ON, 10)
E
E
E
E
E
E
C
(10)
C (10)
C (10)
C (10)
C (10)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C
(30msec)
E
E
E
E
E
E
C
(3)
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
C
(3)
E
E
E
E
E
E
E
E
E
E
Mode
(Note 1) BASS: +6 dB, TREBLE: 0 dB
(Note 2) BASS: +8 dB, TREBLE: 4 dB
C : Adjustable
E : Not adjustable
Signals and adjustability in the different modes
NEO:6
MUSIC MODE ONLY
CENTER IMAGE
E
E
E
E
E
E
E
E
E
C
(0.2)
E
E
E
E
E
E
E
To Next Page
Loading...
