ENGLISH
G
o
•
,
~
A Y "
A~
Preparations
'1"
Press
<SPEAKERS>
to select the front speakers
Front
A,
Front
B
or
Front
A+B. .
*
Do
not hold the microphone
in
your
hand
during measurements,
Be
slJre
that the path'from microphone
to
the
speakers is not
blocked by objects, Avoidplacing
th~
microphone close
to
a seat
back or wall
as
sound reflections may give inaccurate results.
2
'
Set
"Amp
A.SSign".".to
...
d.
efin.
e how the amplifier for
th.e
. surround
back
~ker
channels is used (GT"page 27).
3
Connect the
inclu~edcalibrated
setup microphone
to
•
<SETUP
MIC:;>.
.,
Auto Set
<$tarV:i~
(jispiayed.
4
...
Placethemicr.
op.
hQ.n
....
ea.tearheighton
a triPod.
o.
rstan.d
, _ with the microphone PQinting directly
up
towards
the
ceiling.
When using a subwoofer, make the following settin9s before starting
the auto setup procedure:
• Defeat the volume
and
crossover controls
if
possible
• If this
is
not possible then set
• Volume: "12 o'clock" position
· Crossover frequency: "Maximum/Highest Frequency"
• Low pass filter:
"Off"
· Standby mode:
"Off"
Example(?JExampleCf!
(-:Measuring positions)
• Audyssey MultEO automatically measures the acoustical problems
in
the listening environment to create the best audio experience for
your horne theater.
• Audyssey MultEO optimizes a large listening
area
where one or
more listeners are seated.
Measurements
are
performed by placing the calibrated microphone
(DM-A409) successively at multiple positions throughout the
listening
area
as
shown
in
Example
(j)
For
best results, it
is
strongly
recommended
to measure 6 positions
so
that the measurements
have
the proper spatial weighting,
Even
if
the listening environment
is
small
as
shown
in
Example
i1't.
measuring at multiple points throughout the listening environment
results
in
more effective correction.
•
,.~
>,
*c
About
the I,llain
Ij$t~ning
PP$itjQni(~M)~:,::j':;:~.:::;
The
main listening position refers to the most central position where
one would normally sit within the listening environment.
MultEO uses the measurements from this position
to
calculate
speaker distance,
level,
polarity,
and
the optimum crossover value
for the subwooter.
Pi
To
make
manual
adjustments
to
the settings, see pages
22
-
24.
ENTER
~
..
~.
""
rot;
:c/:
f
::
<SETUP
MIC>
ENTER,
<l
MASTER
VOLUME
~
"V
__________
c_~
o
~W~
"
:
;;:-.'
i7f~~:
<'i''-:/'i-
MASTER
VOLUME
,:,.,//~,\iG)~
;
<:--.~:
'.::/;~
..
__
.-~J
';:-./'
~
"V
<l
~:~
ENTER
•
>'y
••
-.:~~.::~,.;
•
,'"
<SPEAKERS>
Auto
Setup
&Symbols used
,to
,iQ~ic;ate
buttons
in
thismlloulll·
Button located
on
both the
main
unit
and
the remote control
unit •
BUTTON
Button only
on
the main unit •
<BUTTON>
Button only
on
the remote control unit •
[BUTTON]
[Front]
[Rear]
18
To Next Page
Loading...
