ENGLISH
)
)
( Step 2 : Measurement
fa
After completing a measurement position. move the microphone to
the next position.
Measure at
6 positions: the main listening
pOSition
and 5 other
surrounding positions. Although it is allowable to measure less than
6
positions, it
is
recommended to measure 6 for best results.
CD
Press
\l
to
select "2nd Start<". then press
<l.
•
The
measurement of the 2nd position starts.
@ Move the microphone to the 3rd position
and
press
<l.
•
The
measurement of the 3rd position starts.
CD
Perform
et
repeatedly.
• "Calculate<"
is
displayed when you have completed
measurements
in
6 positions.
• If you want
to
stop after measuring just five or fewer positions,
use
\l
to
display"
Calculate<".
-kt,lj_
Do
not change the speaker connections or subwoofer volume after
"Step
1".
• Analysis takes several minutes to complete.
•
The
time required for this analysis depends
on
the number of
speakers connected. The greater the number of speakers connected,
the longer analysis will take.
( Step 3 : Calculation
The
values Obtained from the measurements
are
automatically
analyzed and the attributes for each of the speakers
in
the listening
area
are
determined.
GJ
Press
<l
while "Calculate"
IS
displayed.
• "Calculating"
is
displayed
and
analysis begins.
-No
••
Do
not change the speaker connections
or
subwoofer volume.
or
speaker locations after making measurements. If changes are
necessary. make the changes and
use
the Audyssey MultEO auto
setup once again for
an
updated
EO
solution.
)
If
an
error message appears during the measurements, check "Error
Messages", take the advised action, then start the measurements
again
(Gf'page
20L
Subwoofer
Yes:
".1
",
No:
"0"
Number of surround speakers
or surround back speakers
Number of front speakers or
center speakers
•
To
cancel the measurements, press
<l
while "Measure:FL <Ccl"
is
displayed ("CeI" stands for "Cancel").
The
Audyssey MultEO auto setup function detects the presence of
each speaker
and
automatically calculates the speaker size. channel
level. distance,
and
optimal crossover frequency setting. Audyssey
MultEO corrects acoustical distortions within the listening
area.
Before starting, connect and position
all
of your speakers.
Once started, MultEO will
playa
series of test tones through
each
speaker.
About the Auto Setup
The speaker connection
and
polarity are detected at the first
measurement position
(main
listel"llng position). The following
attriflutes are also determined at this time: "Speaker Size", "Speaker
Distance", "Channel Level", "Crossover Frequency".
(1)
Press
<l
while "Auto Set<Start"
is
displayed.
·While
the measurements are being conducted "Meclsure:FL
<CeI" ("FL" indicates the speaker being measured)
IS
displayed.
• When the measurements
are
completed, "Sp Detect Check"
is
displayed.
Press
ENTER
to display the number of speakers detected.
Example:
For
a
7.1
channel speaker configuration
( Step 1 : Speaker Detection
•
If
the result differs from the actual connection status or
an
error
message appears. use
\l
to display
"Retry<"
and then press
<l
to
repeat the measurement.
• If the result still differs froln the actual connection status after
re-measurement
or
the error message still appears. it
is
possible
that the speakers
are
not connected properly. Turn tile AVR-1609
off, cr,ock the speaker connections and repeat the measurement
process from the beginning.
'~(.jl.
•
Do
not disconnect the setup microphone until the auto setup
procedure
is
completed.
• When using Ileadphones. unplug the headphones before starting
the auto setup procedure.
~w--_,,~'%
~
_-..,,:li~
_~
;;:;"'''''''To
x -
••
v~-
J"N''''
Auto'Setup
Optimize settings
for
speakers
in
use
·~(·ji.
•
Loud
test sounds may
be
played during Audyssey MultEO automatic
speaker setup. This is part of normal operation. If there is background
noise
in
room. these test signals will increase
in
volume.
•
Do
not stand between the speakers and setup microphone or allow
obstacles
in
the path while the measurements
are
being made. This
will cause inaccurate readings.
• Make the room
as
quiet
as
possible. Background noise
can
disrupt
the room measurements. Close windows. silence cell phones.
televisions. rallios. air conditioners, fluorescent lights, home
appliances, light dimmers, or other devices
as
measurements may
be
affected
by
these sounds
Cell
phones
stiOuld
be
placed away from
all
audio electronics during
Hie measurement process
as
Radio
Frequency Interference
(RFI)
may cause measurement disruptions (even if the cell phone
is
not
in
use).
• Operating
MASTER
VOLUME
during the measurements will cancel
the measurements.
19
•
To Next Page
Loading...
