ENGLISH
response of
all
speakers to flat
C
••
Rat
' : Optimize frequency
.......
.,;a
response.
\.'
: Turn equalizer off.
• Audyssey • Audyssey
Byp.
LJR
~
------t.~
OFF
......
>-------<.~
Audyssey Flat
..
-
1m
MultEQ
Select the type of room correction desired from the following list:
elf the settings of speakers for which "None"
has
been determined
at
"Auto Setup"
are
changed, "Audyssey': "Audyssey Byp.
LJR"
and
';A.udyssey
Flat" cannot be selected. Either perform Auto Setup
again,
or return to the setting after running Auto Setup with "System
Setup" - "Speaker Setup" - "Restore".
• When using headphones,
"MultED"
is
set to "OFF".
~
Operating from
the
main unit or remote control
unit
Press
MULlED.
.When
"Audyssey", "Audyssey
Byp.
LJR"
or "Audyssey Flat"
is
selected, the Audyssey MultED indicator lights green.
• After running Auto Setup, if the Speaker Configuration, Distance,
Channel Level
and
Crossover Frequency have changed without
increasing the number
of
speakers measured, the Audyssey MultED
indicator lights
red.
-N·u.
•
"MultED"
can
only
be
set when Auto Setup
has
been performed.
•
"MultED"
cannot be set
in
the following situations.
• If "Auto Setup" fails to be completed.
• Aher running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
III
5ubwoofer
Turn
subwoofer output
on
and
off.
Attenuate subwoofer level when using
EXT.
IN
mode.
[Selectable items]
Set this to
"ON"
if the subwoofer channel level seems too high when
playing audio signal.
..
5UBWOOFER
An:
The
tone cannot
be
adjusted when
in
the
DIRECT
mode.
-No
••
When the "Dynamic ED" setting
is
"ON': setting
is
not possible.
II
Tone Control
Turn
tone adjustments
on
and
off.
[Variable range]
[Selectable items]
I;:'~:';(l:
The
subwoofer
is
used.
~:n~~l~'
The
subwoofer
is
not used.
~~B·
.()8
..
.0::
The
input from the subwoofer channel is attenuated.
..
,l}.."
I
'9Ff.
I:
The
input from the subwoofer channel
is
not attenuated.
Usually use
in
this mode.
IIiIBass
Adjust low frequency range
(bass).
[Variable range]
ia.~
-
[jiM'"
-
~~
Ii
Treble
Adjust high frequency
range
(treble).
[Selectable items]
Ilqrt:":
Allow tone adjustment (treble, bass).
I:Oif
:,1:
Playback
without tone adjustment.
.
MTRXON,
The
surround channel signals undergo digital matrix
processing
and
are
output from the surround
back
channels.
*1
'Pl.IJJJL",
:Decoded
in
Dolby
Pro
Logic
llx
Cinema mode,
surround
back
signal played.
a.l~~
*2 : Decoded
in
Dolby
Pro
Logic Ilx Music mode,
surround
back
signal played.
£$MTRX
*3 :
DTS
signal played with digital matrix processing.
~Miol.;~"""",,mm._
&U8I;
*4 : Signal included
in
DTS-ES
Discrete 6.1-channel
sources played.
*
1:
This
can
be
selected when "Surround
Back
Speaker"
is
set
to
"2spkrs"
at
the "System Setup" - "Speaker Setup" setting
(Grpage
22).
*
2:
This
can
be selected when "Surround
Back
Speaker"
is
set to
"2spkrs"
or
"1
spkr"
at
the"
System Setup" - "Speaker Setup"
setting.
*
3:
This
can
be
selected when playing
DTS
sources.
*
4:
This
can
be
selected when playing
DTS
sources including a
discrete 6.1-channel signal identification signal.
[Selectable items]
II
5B
CH
OUT
(for
Multi-channel
sources)
Select playback mode for surround
back
channels.
No
signal
is
played from the surround back
channels.
Settings
can
also be made when
[SID]
is
pressed.
When using surround back speakers, adopt the following
settings.
CD
Adopt
M7.1CW
for the
AMP
Assign setting.
• The default setting for the Amp Assign mode of AVR·1609
is
MZONE2~
CV
Adopt a setting other than
MOFF-
for the
MSB
CH
OUT-
setting
of
MSurround
Parameter~
II
5B
CH
OUT
(for 2-channel sources)
Determine whether to use surround
back
speakers.
[Selectable items]
,;,:;e!3l1:
The
surround
back
channel signal
is
played.
:".,nl;l:l):;;::
The
surround
back
channel signal
is
not played.
~$~IJ:~lh:;
•
"Bass"
and
"Treble"
can
be set when "Tone Defeat"
is
set to "OFF".
33 IFor details
on
adjusting individual parameters. see UAdjusting
the
parameters- (Gr"page 31).
To Next Page
Loading...
Need help?
General
