ENGLISH
•
Audyssey Dynamic VolumeT
M
solves the problem of large variations
in
volume level between television programs, commercials, and
between the soft and loud passages of movies.
DynamicVolumelooks at the preferred volume setting by the user and
then monitors
how
the volume of program material is being perceived
by
listeners
in
real
time to decide whether
an
adjustment
is
needed.
Whenever necessary, Dynamic Volume makes the necessary rapid
or gradual adjustments
to
maintain the desired playback volume
level while optimizing the dynamic range. Audyssey Dynamic
EO
is
integrated into Dynamic Volume
so
that
as
the playback volume
is
adjusted automatically, the perceived bass response, tonal balance,
surround impression, and dialog clarity remain the same whether
watching movies, flipping between television channels, or changing
from stereo to surround sound content.
Audyssey Dynamic
EOTM
solves the problem of deteriorating sound
quality
as
volume is decreased by taking into account human
perception and room acoustics. Dynamic
EO
selects the correct
frequency response and surround levels moment-by-moment at
any user-selected volume setting. The result is bass response,
tonal balance, and surround impression that remain constant
despite changes
in
volume. Dynamic
EO
combines information
from incoming source levels
with
actual output sound levels
in
the
room, a prerequisite for delivering a loudness correction solution.
Audyssey Dynamic
EO
works
in
tandem with Audyssey MultEO to
provide well-balanced sound for every listener at any volume level.
II
DV Setting (Dynamic Volume Setting)
Set Dynamic Volume effect.
[Selectable items]
I~«dljd:
High setting affects volume the most, causing
all
sounds
to
be of equal loudness.
~:l.!iis~:
Middle setting prevents loud and
soft
sounds from
being much louder and softer respectively than average
sounds.
,
~!t;0.'liJ:
Low
setting provides the least adjustments
to
the
loudest and softest of sounds.
-~[-jj-
• "DV Setting"
can
only be set when auto setup
has
been performed.
• "DV Setting" cannot be set
in
the following situations.
• If "Auto Setup" fails to be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• If "Dynamic Volume" setting is "OFF':
"Red"
Dynamic
EO
:
ON
/
Volume:
OFF
[~ors~l
~o-
/1
'
"Green"
Dynamic
EO
/
Volume:
ON
--
[~~l
~-
_~[ui_
• "Dynamic Volume"
can
only be set when auto setup
has
been
performed.
• "Dynamic Volume" cannot be set
in
the following situations.
• If "Auto Setup" fails
to
be completed.
• After running Auto Setup, when the number of used speakers
has
increased from the number of measured speakers.
• When
"MultEO"
is
set
to
"OFF", "Dynamic EO" is automatically set
to "OFF".
• "Night Mode" and "Tone Control" cannot be used jointly.
[Selectable items]
Dynamic
EO
/
Volume:
OFF
II
Dynamic Volume
Audyssey Dynamic Volume solves the problem of large variations
in
volume level between television programs, commercials, and between
the soft and loud passages of movies.
Audyssey Dynamic
EO
is
integrated into Dynamic Volume
so
that
as
the playback volume is adjusted automatically, the perceived bass
response, tonal balance, surround impression, and dialog clarity
remain the same.
Operating from the unit or remote control
unit
Press
<DYN
VOl>
or
[DYNAMIC
VOLUME].
Use Dynamic Volume.
The
Dynamic Volume effect will be at the level of the "DV
Setting".
I··
Off:il:
Do
not use Dynamic Volume.
Before running Auto Setup and after running Auto Setup, if the number
of speakers
has
increased
or
you pressed
<DYN
VOl>
or
[DYNAMIC
VOLUME],
"Run Audyssey"
is
displayed. In this case, either perform
Auto Setup again, or return to the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
1m
Dynamic
EQ
Audyssey Dynamic
EO
solves the problem of deteriorating sound
quality
as
volume
is
decreased
by
taking into account human perception
and room acoustics. Audyssey Dynamic
EO
works
in
tandem with
Audyssey MultEO to provide well-balanced sound for every listener
at
any
volume level.
-n-u-
• "Dynamic EO"
can
only be set when auto setup
has
been
performed.
• "Dynamic EO" cannot be set
in
the following situations.
•
If
"Auto Setup" fails
to
be completed.
• After running Auto Setup, when the number of used speakers has
increased from the number of measured speakers.
• When
"MultEO"
is set to "OFF': "Dynamic EO"
is
automatically set
to "OFF".
• "Night Mode" and "Tone Control" cannot
be
used jointly.
[Selectable items]
~~:i:
~:en~:::~:Y:~~~cn::;unction.
OOperating conditions for each function
• Dynamic
EQ
: When
"MultEO"
is
set to
"ON"
• Dynamic
Volume:
When "Dynamic EO"
is
set to
"ON"
• DV setting: When "Dynamic Volume"
is
set to
"ON"
Operating from the unit or remote control
unit
Press
<DYN
VOl>
or
[DYNAMIC
VOLUME]
C
Dynamic
EO
/
Volume:
ON
---
Dynamic
EO
:
ON
/
Volume:
OFF
~
-
Dynamic
EO
/
Volume:
OFF
.....
t------~
II
Before running Auto Setup and after running Auto Setup, if the number
of speakers
has
increased or you pressed
<DYN
VOl>
or
[DYNAMIC
VOLUME],
"Run Audyssey"
is
displayed.
In
this case, either perform
Auto Setup again, or return
to
the setting after running Auto Setup with
"System Setup" - "Speaker Setup" - "Restore".
For details on adjusting individual parameters, see "Adjusting
the
parameters"
(~page
31).1 34
To Next Page
Loading...
Need help?
General
