To Next PageTo Next PageWhy won't my Denon AVR-1707 turn on, no display and no sound?
If the display is not lit and no sound is produced when the power switch is set to on, check the insertion of the power supply cord plug to ensure it is securely plugged in.
What to do if no sound is produced from subwoofer of Denon AVR-1707 Stereo Receiver?
If no sound comes from the subwoofer, check the following: * Ensure the subwoofer's power is turned on. * Verify the subwoofer’s initial setting is set to “YES”. * Confirm the subwoofer’s output is properly connected. * Check that the subwoofer’s channel volume level is not set to “OFF”; turn it up if necessary.
Why is there no DTS sound from my Denon AVR-1707 Stereo Receiver?
If you're not getting any DTS sound, first, make sure the DVD player’s audio output setting is set to bit stream, or make the DVD player’s default settings. Also, confirm that your DVD player is DTS-compatible; if not, use a DTS-compatible player. Lastly, check that the receiver's input setting is set to “AUTO” or “DTS,” not analog.
Why is my Denon Stereo Receiver display lit but there's no sound?
If your Denon Stereo Receiver's display is lit but there's no sound, consider these potential causes: * Ensure the speaker cables are securely connected. * Verify that the INPUT SELECTOR knob is in the correct position. * Check that the volume isn't set to the minimum; increase it to a suitable level. * Confirm that MUTING is switched off. * If using a digital signal, ensure a digital signal input source is properly selected.
Why is there no sound from my Denon Stereo Receiver subwoofer?
If there's no sound coming from the subwoofer connected to your Denon Stereo Receiver, consider the following: * Ensure the subwoofer is powered on. * Check that the subwoofer's initial setting is set to “YES”. * Verify that the subwoofer's output is properly connected. * Make sure the subwoofer's channel volume level is not set to “OFF”; increase the volume level.
Why is there no DTS sound on my Denon Stereo Receiver?
If your Denon Stereo Receiver isn't producing DTS sound, check these potential causes: * Ensure the DVD player’s audio output setting is set to bit stream by making the DVD player’s default settings. * Confirm that your DVD player is DTS-compatible; use a DTS-compatible player if needed. * Verify that the receiver’s input setting is set to “AUTO” or “DTS”.
What does it mean when the power indicator is blinking red on my Denon Stereo Receiver?
If your Denon Stereo Receiver's power has turned off and the power indicator is blinking red, it indicates that the protection circuit has been activated. This could be due to a few reasons: * The unit's internal temperature may have risen. In this case, place the receiver in a well-ventilated area. * The core wires of the speaker cables might be touching each other or the receiver's rear panel. Inspect and correct all speaker cable connections. * The receiver might be malfunctioning.
Why can't I copy from DVD to VCR with my Denon Stereo Receiver?
Copying between a source such as DVD and a VCR is often not possible because DVDs are frequently encoded with copy-protection signals that prevent VCR recording. Therefore, copying is not possible.
Why is “DOLBY DIGITAL” not displayed on my Denon AVR-1707 Stereo Receiver?
If “DOLBY DIGITAL” is not displayed, the DVD player’s digital audio output setting may not be proper. Check the DVD player’s audio output setting.
How to fix no display on monitor connected to Denon AVR-1707 Stereo Receiver?
If nothing is displayed on the monitor, verify that the receiver's video output terminals and the monitor's input terminals are correctly connected. Also, ensure that the monitor's input setting is set to the correct terminals to which the video signals are connected. If you're using a player connected with a component terminal and a TV connected with a video (yellow) or S-Video terminal, note that down-conversion is not possible for progressive video signals; adjust the interlace settings on the player.
General| Speakers connectivity type | - |
|---|---|
| Receiver type | Surround |
| Frequency range | 10 - 100000 Hz |
| Audio output channels | 7.1 channels |
| Audio A/D Converter (ADC) | 24-bit/96kHz |
| Total Harmonic Distortion (THD) | 0.7 % |
| Power output per channel (1KHz@6 Ohm) | 110 W |
| Power output per channel (20-20KHz@8 Ohm) | 75 W |
| Product color | Silver |
| Audio decoders | DTS, DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital, Dolby Digital EX, Dolby Pro Logic II, Dolby Pro Logic IIx |
| Apple docking compatibility | iPod |
| Digital Signal Processing (DSP) | Yes |
| HDMI in | 0 |
| Digital audio optical in | 2 |
| Component video (YPbPr/YCbCr) in | 3 |
| Optical drive included | No |
Weight and Dimensions| Depth | 417 mm |
|---|---|
| Width | 434 mm |
| Height | 147 mm |
| Weight | 11400 g |
Check continuity between chassis and power cord to prevent electrical hazards.
Warning about touching internal metal parts when energized and high voltage parts.
Use only replacement parts with the same safety properties as original ones.
Verify all parts are reassembled correctly and perform insulation checks.
Parts marked with '!' have critical safety properties and must be replaced with designated parts.
Procedure to initialize the receiver when µcom or related parts are replaced.
Adjusting the idling current for the audio output stage using a DC voltmeter.
Adjusting signal levels of S MONITOR OUT and COMPONENT OUT using oscilloscope.
List of parts for the C/S Video 1 PWB, categorized by component type.
List of parts for the CPU PWB, categorized by component type.
List of semiconductor parts for the pre-amp PWB.
List of parts for the CNT PWB, categorized by component type.
List of parts for the input PWB, categorized by component type.
List of parts for the 8CH-EXT XM PWB, categorized by component type.
List of parts for the 8CH-EXT(E2) PWB, categorized by component type.
List of parts for the DSP1 PWB, categorized by component type.
List of parts for the main PWB, categorized by component type.
