Denon AVR-4800 User Manual

34
“VCR”
A
B
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t (V. AUX)
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE-1)
(VCR-2)
p
(SHIFT)
SHIFT
(CHANNEL +)
CHANNEL
+
(CHANNEL -)
CHANNEL
–
(A/B)
A / B
(DIRECT)
DIRECT
—
HITACHI A
MITSUBUSHI A
JVC (VICTOR) A
PANASONIC A
SONY A
PIONEER
TOSHIBA A
SANYO A
SHARP A
NEC A
PHILIPS A
RCA A
GENERAL
ELECTRIC A
—
(STEREO)
STEREO
—
HITACHI B
MITSUBUSHI B
JVC (VICTOR) B
PANASONIC B
SONY B
—
TOSHIBA B
SANYO B
SHARP B
NEC B
PHILIPS B
RCA B
GENERAL
ELECTRIC B
—
(EXT. IN)
EXT.IN
—
—
MITSUBUSHI C
JVC (VICTOR) C
PANASONIC C
SONY C
—
—
—
—
NEC C
PHILIPS C
—
—
—
Preset codes set upon shipment from the factory
“TV”
A
B
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t (V. AUX)
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE-1)
(VCR-2)
p
(SHIFT)
SHIFT
(CHANNEL +)
CHANNEL
+
(CHANNEL -)
CHANNEL
–
(A/B)
A / B
(DIRECT)
DIRECT
—
DENON/HITACHI
MITSUBUSHI A
JVC (VICTOR)
PANASONIC A
SONY
PIONEER
TOSHIBA
SANYO
SHARP
NEC
PHILIPS
RCA
GENERAL
ELECTRIC A
MAGNAVOX
(STEREO)
STEREO
—
—
MITSUBUSHI B
—
PANASONIC B
—
—
—
—
—
—
—
—
GENERAL
ELECTRIC B
—
(EXT. IN)
EXT.IN
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control
unit’s transmitting window while setting the preset memory.
• Some models and years of manufacture of components of the manufacturers listed on Table 1 cannot be used.
• The signals stored at “learned” buttons have priority over the preset codes. If you wish to clear the “learned” signals, do so as described
on page 39.
• Some manufacturers use different types of remote control codes for their products. If the component does not operate when set to remote
codeset A, try setting to the B or C codesets.

Denon AVR-4800 Specifications

Power Amplifier

stereo rated output	125 W + 125 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)
surround rated output	125 W x 5 ch (8 Ω/ohms, 1 kHz with 0.7% T.H.D.)
dynamic power	170 W x 2 ch (8 Ω/ohms), 270 W x 2 ch (4 Ω/ohms), 350 W x 2 ch (2 Ω/ohms)

Analog Audio

input sensitivity / input impedance	200 mV / 47 kΩ/kohms
frequency response	10 Hz ~ 100 kHz: +0, –3 dB (DIRECT mode)
S/N ratio	105 dB (DIRECT mode)

Digital Audio

D/A output rated output	2 V (at 0 dB playback)
total harmonic distortion	0.005% (1 kHz, at 0 dB)
S/N ratio	105 dB

Phono Equalizer

input sensitivity	2.5 mV
RIAA deviation	±1 dB (20 Hz to 20 kHz)
signal-to-noise ratio	74 dB (A weighting, with 5 mV input)

Video

standard video jacks input/output level and impedance	1 Vp-p, 75 Ω/ohms
S-video jacks input/output level and impedance	Y signal — 1 Vp-p, 75 Ω/ohms; C signal — 0.286 Vp-p, 75 Ω/ohms
color component video terminal input/output level and impedance	Y signal — 1 Vp-p, 75 Ω/ohms; Cb signal — 0.7 Vp-p, 75 Ω/ohms; Cr signal — 0.7Vp-p, 75 Ω/ohms

Tuner

receiving range	87.5 MHz ~ 107.9 MHz, 520 kHz ~ 1710 kHz
usable sensitivity	1.0 µV (11.2 dBf), 18 µV
signal to noise ratio (IHF-A)	MONO 80 dB, STEREO 75 dB

General

power supply	AC 120 V, 60 Hz
power consumption	10.9 A
maximum external dimensions	434 (W) x 181 (H) x 494 (D) mm (17-3/32” x 7-1/8” x 19-29/64”)

Remote Control Unit

batteries	R6P/AA Type (two batteries)
external dimensions	70 (W) x 215 (H) x 24 (D) mm (2-3/4” x 8-15/32” x 15/16”)
weight	200 g (Approx. 7 oz) (including batteries)