EasyManuals Logo

Denon AVR-4800 User Manual

Denon AVR-4800
69 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #33 background imageLoading...
Page #33 background image
33
Preset memory
Denon and other makes of components can be operated by setting the preset memory for your make of video component. Operation is not
possible for some models, however. In this case use the learning function (see page 36) to store the remote control signals.
For instructions on clearing the presettings stored in the preset memory, see page 39.
1
Set the slide switch to “VIDEO”.
AVR/AVC VIDEO
AUDIO
2
Set the slide switch to the component to
be registered (DVD, VDP, VCR or TV).
DVD TV
VDP VCR
CD
MD
MULTI
DECK
Keep the POWER button pressed in
when performing steps 3 and 4
()
3
Holding in the POWER button, press the
button for the corresponding manufacturer
in block A.
(Refer to Table 1.)
Flashes
The LEARNED/TX LED flashes.
4
Next, while holding the POWER button,
press the button for the code in block B.
(Refer to Table 1.) The operation is
completed when the button is released and
the LEARNED/TX LED lights.
5
To continue registering other components,
repeat steps 2 to 4.
DVD
START LEARNED/TX
HOME THX CINEMA
TUNING
BAND
TITLE
MENU/GUIDE
MODE
MEMORY
USE/LEARN T.TONE MULTI SPEAKER DVD
SET UP
RETURN
STATUS
DISPLAY
ON SCREEN
DOLBY / DTS
SURROUND
DIRECT
DSP SIMULATION
5CH / 7CH STEREO
STEREO
INPUT MODE
ANALOG EXT.IN
MUTING
MASTER VOL.
VOLUME DISC SKIP+
SYSTEM CALL POWER
VDP TUNER SHIFT
TV/DBS V.AUX PHONO
VCR-1 CD
MD
/
TAPE-1
CHANNEL
VCR-2
TAPE-2 MON
TV/VCR
AVR/AVC VIDEO DVD TV
AUDIO
VDP VCR
CD
MD
MULTI
DECK
SYSTEM
SETUP
SURROUND
PARAMETER
CH SELECT
SELECT
RC-869
123
4
SET
A / B
CALL OFF
ENTER
ON
/
SOURCE
56
789
+10
0
3
3,4
4
2
1
This remote control unit can be used to operate components of other manufacturers without using the learning function by registering the
manufacturer of the component as shown on Table 1.
Table 1: Combinations of Personal System Codes for Different Manufacturers
“DVD”
A
B
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t (V. AUX)
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE-1)
(VCR-2)
p
(SHIFT)
SHIFT
(CHANNEL +)
CHANNEL
+
(CHANNEL -)
CHANNEL
(A/B)
A / B
(DIRECT)
DIRECT
DENON A
PANASONIC
SONY
PIONEER
TOSHIBA
(STEREO)
STEREO
DENON B
(EXT. IN)
EXT.IN
“VDP”
A
B
q (DVD)
w (VDP)
e (TUNER)
r (TV/DBS)
t (V. AUX)
y (PHONO)
u (VCR-1)
i (CD)
o (MD/TAPE-1)
(VCR-2)
p
(SHIFT)
SHIFT
(CHANNEL +)
CHANNEL
+
(CHANNEL -)
CHANNEL
(A/B)
A / B
(DIRECT)
DIRECT
DENON A
MITSUBISHI
PANASONIC
SONY A
PIONEER
PHILIPS
RCA
MAGNAVOX
(STEREO)
STEREO
DENON B
SONY B
(EXT. IN)
EXT.IN
DENON C
SONY C
Preset codes set upon shipment from the factory

Other manuals for Denon AVR-4800

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-4800 and is the answer not in the manual?

Denon AVR-4800 Specifications

Power Amplifier IconPower Amplifier
stereo rated output125 W + 125 W (8 Ω/ohms, 20 Hz ~ 20 kHz with 0.05% T.H.D.)
surround rated output125 W x 5 ch (8 Ω/ohms, 1 kHz with 0.7% T.H.D.)
dynamic power170 W x 2 ch (8 Ω/ohms), 270 W x 2 ch (4 Ω/ohms), 350 W x 2 ch (2 Ω/ohms)
Analog Audio IconAnalog Audio
input sensitivity / input impedance200 mV / 47 kΩ/kohms
frequency response10 Hz ~ 100 kHz: +0, –3 dB (DIRECT mode)
S/N ratio105 dB (DIRECT mode)
Digital Audio IconDigital Audio
D/A output rated output2 V (at 0 dB playback)
total harmonic distortion0.005% (1 kHz, at 0 dB)
S/N ratio105 dB
Phono Equalizer IconPhono Equalizer
input sensitivity2.5 mV
RIAA deviation±1 dB (20 Hz to 20 kHz)
signal-to-noise ratio74 dB (A weighting, with 5 mV input)
Video IconVideo
standard video jacks input/output level and impedance1 Vp-p, 75 Ω/ohms
S-video jacks input/output level and impedanceY signal — 1 Vp-p, 75 Ω/ohms; C signal — 0.286 Vp-p, 75 Ω/ohms
color component video terminal input/output level and impedanceY signal — 1 Vp-p, 75 Ω/ohms; Cb signal — 0.7 Vp-p, 75 Ω/ohms; Cr signal — 0.7Vp-p, 75 Ω/ohms
Tuner IconTuner
receiving range87.5 MHz ~ 107.9 MHz, 520 kHz ~ 1710 kHz
usable sensitivity1.0 µV (11.2 dBf), 18 µV
signal to noise ratio (IHF-A)MONO 80 dB, STEREO 75 dB
General IconGeneral
power supplyAC 120 V, 60 Hz
power consumption10.9 A
maximum external dimensions434 (W) x 181 (H) x 494 (D) mm (17-3/32” x 7-1/8” x 19-29/64”)
Remote Control Unit IconRemote Control Unit
batteriesR6P/AA Type (two batteries)
external dimensions70 (W) x 215 (H) x 24 (D) mm (2-3/4” x 8-15/32” x 15/16”)
weight200 g (Approx. 7 oz) (including batteries)

Related product manuals