76
Section 6
Parts Data
V-Series
Accessories
WCVD18KCS-10 120 volts 60hz. Single Phase
WCVD18KCS-12 208-240 volts 60hz. Single Phase or Three Phase
WCVD25KCS-12 208-240 volts 60hz Single Phase or Three Phase
WCVD40KCS-12 208-240 volts 60hz Single Phase or Three Phase
WCVD55KCS-12 208-240-volts 60hz Single Phase or Three Phase
WCVD75KCS-12 208-240 volts 60 hz Single Phase or Three Phase
Grip-O-Matic #1045 Puller to Remove Pulley and Bearing Housing from Shaft on 25lb and 40lb
9732-139-002 Kit, Door Gasket Expander (large)
9732-139-001 Kit, Door Gasket Expander (small)
9990-027-011 Hose, Water Supply (furnished 18lb.,25lb.,40lb.) 3/8" I.D. x 48" . 2
9990-027-013 Hose, Water Supply (furnished 55lb.,75lb.) 5/8" I.D. x 48" .......... 2
8641-242-000 Washer, Inlet Hose (furnished) ..................................................... 2
9565-003-001 Strainer, Inlet Hose (furnished) ..................................................... 2
9242-417-002 Drain hose 10 ft. length x 2-1/4" I.D. ...........................................
9242-417-003 Drain hose 10ft. length x 3" I.D. ................................................
8641-586-002 Bevel Washer for 5/8" bolt used in installations using angle iron bases
8641-586-003 Bevel Washer for 3/4" bolt used in installations using angle iron bases
8538-151-001 Sealing compound ........................................................................
8545-051-002 TORX#20 ......................................................................................
8545-051-003 Special Tool For Removing Coin Acceptor Mounting Screws. (T-10 Torx)
9475-002-002 Flow Restrictors ( in dispenser ) ................................................... 2
8612-001-001 Battery (used on Control PCB) ..................................................... 1
8545-056-001 Special Tool for adjusting spacing between outer tub front and cylinder front
on WCVD-55 ,WCVD-75
9183-036-001 VFD Filter options 75-55-40 lb ......................................................
9183-033-001 VFD Filter options 75-55-40 lb ......................................................
Snap On #CJ-84-C Puller for pushing cylinder out of bearings must be purchase from local sources.
Clamps to hold tub front to outer tub when installing tub front WCVD-55,WCVD-75
Vise Grip
#11R
9504-010-001
9732-325-001
9732-226-009
9732-226-008
9732-226-007
9732-226-006
9732-226-005
9732-226-004
9732-226-003
9732-226-002
9732-226-001
9732-224-001
Coin OP CD for OS2 platform for infared programming devices
K
it - Replaces the 9376-301-001 motor
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
Emergency Stop Conversion Kit - V series to A series
V & A series conversion to manual start for small vault
To Next Page
Loading...
Need help?
General
