Need help?Do you have a question about the Digitus DA-81002 and is the answer not in the manual?
General| Type | Handheld bar code reader |
|---|---|
| Sensor type | CMOS |
| Scanner type | 1D/2D |
| Read rate (max) | 200 reads/s |
| Maximum scan width | 100 mm |
| Tilt reading angle | -60 - 60 ° |
| Linear (1D) barcodes supported | Codabar, Code 128, Code 32, Code 39, Code 93, EAN 128, EAN-13, EAN-8, GS1 DataBar, GS1-128 (UCC/EAN-128), IATA, ISSN, ITF-14, ITF-6, Industrial 2 of 5, MSI, U.P.C. |
| 2D (matrix & stacked) barcodes supported | Data Matrix, PDF417, QR Code |
| Input voltage | 5 V |
| Power consumption | 120 mA |
| Power source type | USB |
| Cable length | 2 m |
| Standard interfaces | RJ-45, USB |
| Connectivity technology | Wired |
| Storage temperature (T-T) | -40 - 70 °C |
| Operating temperature (T-T) | -20 - 50 °C |
| Product color | Black |
| Housing material | Acrylonitrile butadiene styrene (ABS), Polycarbonate (PC) |
| Country of origin | China |
| International Protection (IP) code | IP54 |
| Compatible operating systems | Mac/Linux |
| Mobile operating systems supported | Android, iOS |
| Windows operating systems supported | Yes |
| Harmonized System (HS) code | 84716070 |
Weight and Dimensions| Depth | 87 mm |
|---|---|
| Width | 63 mm |
| Height | 165 mm |
| Weight | 120 g |
Configure reading module using setting codes.
Resets the device to factory default settings.
Save and load custom user default settings.
Select communication modes like USB-HID and TTL-232.
Details of the TTL-232 serial communication interface.
Set the baud rate for TTL-232 communication.
Select HID device types: KBW or POS.
Set the PC to HID device access cycle time.
Set the time interval before HID release.
Set the time interval after HID release.
Configure the Caps Lock behavior.
Enable HID output of a leading message.
Configure manual reading mode with trigger button.
Select between edge and level trigger modes.
Set the maximum duration for a single reading attempt.
Enable or disable deep sleep mode for power saving.
Configure idle time for light sleep mode.
Configure command trigger mode for reading.
Configure continuous scanning mode.
Set the interval between successful readings.
Prevent multiple reads of the same barcode.
Enable reading based on environmental changes or trigger.
Adjust sensitivity for induction reading mode.
Set image stabilization time for induction mode.
Settings for the illumination LEDs.
Settings for the aiming laser.
Turn all prompt sounds on or off.
Detailed settings for passive and active buzzers.
Configure passive buzzer frequency and mode.
Configure active buzzer behavior.
Enable/disable prompt tones for setting codes.
Enable/disable power-on prompt sound.
Configure success prompts (LED, beep, tone).
Set character encoding format for output data.
Select keyboard layout for different countries.
Enable virtual keyboard output.
Select output methods for control characters.
How control characters are transmitted via virtual keyboard.
Enable or disable image mirroring.
Enable or disable reading of inverted barcodes.
Set up local or online invoicing modes.
Read the device's software version.
Read and write a unique device identifier.
Edit data before output (prefix, suffix, interception).
Configure a prefix to be added to decoded data.
Configure a suffix to be added to decoded data.
Enable or prohibit the addition of Code IDs.
Customize Code IDs for various barcode symbologies.
Set terminator characters (CR, TAB, CRLF) for output.
Intercept and modify parts of the decoded data.
Select data segments (start, middle, end) for output.
Adjust the length of data segments.
Configure information output upon reading failure.
Set the output protocol format for decoded results.
Replace GS characters for better display.
Enable or disable URL code reading.
Quick configuration for serial port and full code open mode.
Quick configuration for POS operation mode.
Global settings for barcode reading enablement and defaults.
Enable/disable reading globally and default symbology.
Control output of check digits for product barcodes.
Enhance barcode reading for difficult codes.
Settings specific to EAN12 barcode reading.
Enable or disable EAN13 barcode reading.
Control forced output of EAN13 additional codes.
Enable or disable EAN8 barcode reading.
Control forced output of EAN8 additional codes.
Enable or disable UPC-A barcode reading.
Control forced output of UPC-A additional codes.
Enable or disable UPC-A to EAN13 conversion.
Enable or disable UPC-E0 barcode reading.
Control forced output of UPC-E0 additional codes.
Enable or disable UPC-E1 barcode reading.
Control forced output of UPC-E1 additional codes.
Enable or disable Code 128 barcode reading.
Set min/max reading length for Code 128.
Enable or disable Code 39 barcode reading.
Set min/max reading length for Code 39.
Configure start/end characters for Code 39 output.
Enable or disable Code 32 mode for Code 39.
Enable or disable Full Asc mode for Code 39.
Enable or disable Code 93 barcode reading.
Set min/max reading length for Code 93.
Configure start/end characters for Code 93 output.
Enable or disable Codabar barcode reading.
Set min/max reading length for Codabar.
Configure start/end characters for Codabar output.
Enable or disable Interleaved 2 of 5 reading.
Set min/max reading length for Interleaved 2 of 5.
Enable or disable Industrial 25 reading.
Set min/max reading length for Industrial 25.
Enable or disable Matrix 2 of 5 reading.
Set min/max reading length for Matrix 2 of 5.
Set verification format for Matrix 2 of 5.
Enable or disable Code 11 reading.
Set min/max reading length for Code 11.
Set verification method for Code 11.
Enable or disable MSI reading.
Set min/max reading length for MSI.
Enable or disable RSS-14 reading.
Enable or disable Limited RSS reading.
Enable or disable Extended RSS reading.
Set min/max reading length for Extended RSS.
Enable or disable QR Code reading.
Enable or disable Data Matrix reading.
Enable or disable PDF417 reading.
Save the current configuration settings.
Cancel current or previous reading operations.
Guidelines for setting multiple parameters via QR code.
To Next Page
