40
[350] - Communicator Format Options
Communicator - Reporting Formats
Each central station telephone number of the panel can be pro-
grammed to report using any one of the 5 formats available. The
following formats are supported: Pulse (10 and 20 BPS), Contact
ID, SIA, Residential Dial and a Pager format. The following is a
description of each.
SIA (Level 2)
SIA is a specialized format that will communicate information
quickly using frequency shift keying (FSK) rather than pulses. The
SIA format will automatically generate the type of signal being
transmitted, such as Burglary, Fire, Panic etc. The two digit
reporting code is used to identify the zone or access code
number.
NOTE: SIA format must be used if Downlook is required.
If the SIA format is selected the panel can be programmed to
automatically generate all zone and access code numbers elimi-
nating the need to program these items.
If the SIA Sends Automatic Reporting Codes option is
enabled the panel will operate as follows:
1. If the reporting code for an event is programmed as [00] the
panel will not attempt to call the central station.
2. If the reporting code for an event is programmed as anything
from [01] to [FF] the panel will AUTOMATICALLY generate the
zone or access code number.
3. Bypassed zones will always be identified when partial closing
the system.
The Communicator Call Direction Options can be used to disable
reporting of events such as Openings/Closings. Also, if all the
Opening/Closing reporting codes were programmed as [00] the
panel would not report.
If the SIA Sends Automatic Reporting Codes option is dis-
abled the panel will operate as follows:
1. If the reporting code for an event is programmed as [00] or
[FF] the panel will not attempt to call the central station.
2. If the reporting code for an event is programmed as anything
from [01] to [FE] the panel will send the programmed report-
ing code.
3. Bypassed zones will not be identified when partial closing the
system.
NOTE:
Do not program the second telephone number for the SIA
reporting code format (Section [360]) if the Automatic Reporting
Code option is enabled (Section [381]).
NOTE: The zone number for Zone Low Battery and Zone Fault
events will not be identified when Programmed SIA is used.
SIA Sends Automatic Reporting Codes Section [381], Option [3]
Communicator Call Direction Options. . . Section [351] to [376]
SIA Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Appendix A
Residential Dial
If Residential Dial is programmed and an event that is pro-
grammed to communicate occurs, the panel will seize the line
and dial the appropriate telephone number(s). Once the dialing
is complete, the panel will emit an ID tone and wait for a hand-
shake (press a 1, 2, 4, 5, 7, 8, 0, ✱ or # key from any telephone).
It will wait for this handshake for the duration of Post Dial Wait
for Handshake timer. Once the panel receives the handshake, it
will emit an alarm tone over the telephone line for 20 seconds. If
several alarms occur at the same time, only one call will be made
to each telephone number the panel is programmed to call.
NOTE: The Residential Dial format will not work over the
LINKS1000.
Communicator Call Direction Options. . . Section [361] to [368]
Pager Format
The Communicator Format option for either telephone number
can be programmed for Pager Format. If an event occurs and the
Communicator Call Direction options direct the call to a tele-
phone number with the Pager Format selected the panel will
attempt to page.
When calling a pager extra digits will be required to make it
work properly.The following is a list of Hex digits and what func-
tion they perform:
Hex [A] - not used
Hex [B] - simulates the [] key on a touch tone telephone
Hex [E] - two second pause
Hex [C] - simulates the [#] key on a touch tone telephone
Hex [F] - end of telephone number marker
Hex [D] - forces the panel to search for dial tone
3, 4, 5, 6, PC5700 TLM Line 1/2
Troubles & Restore
These codes are sent when a TLM Trouble/Restore occurs on the PC5700 Line 1 and 2.
[320]-[349] REPORTING CODES
Option Report Code Description
To Next Page
Loading...
