Eaton CF2000 - Application Guide Manual

94 pages

To Next Page

DF6000 Applications Guide

Including CF3000 & FX6000, CF11/1200, DF61/6200

Annex 1 – CF2000

Main Page

DF6000 Applications Guide1
Table of Contents2
Contents2
Recent Amendments6
Introduction8
Panel Firmware Version8
Site Installer Software Version9
Menu Structure10
User Access Code10
Engineers Menu10
Loading and Totals11
Zones12
Access Codes12
User Menu Functions12
Disable/Enable Devices13
Weekly Test13
Check Auto Config13
Replace Device14
Delays14
Double Knock15
Coincidence (Dependency Type C)15
Sounder Level Test15
One man Walk Test16
Test Device16
Auto Learn16
Autolearn by Loop17
Pre-Addressed Autolearn17
Maintenance Autolearn17
Analogue Level19
Printer Settings19
Programming I/O and Sounders & Sub- Menus20
Panel Outputs20
T1 & T221
Alarm Verification Feature24
Auxiliary Board24
HMO Mode24
Class Change25
HMO Zones25
Reset Timeout25
HMO Programming25
Sounder Tone26
FRE Double Knock Override26
Change Text26
Set Date/Time27
Configure Zones27
Input Programming28
Input Programming General Rules30
Output Programming31
Zone Groups and DN any Zone 2 Devices33
Sounder Settings35
Add/Delete38
Configure Heat Detectors39
Network Programming39
Day / Night Settings40
High Level Menus41
Buzzer Disabled / Enabled41
Enable / Disable All Outputs41
Optical Detector Sensitivity42
Australian FB Screen42
Local Zones42
Activate on Evacuate43
Intermittent Fault Search43
Logos43
Reset to Factory Settings44
UL 864 9 Th Edition44
Autolearn Locking44
Evacuate Locking44
Daylight Saving45
BS 5839 Button45
Global Weekly Walk Tests45
Non-Latching RF Faults46
Conventional Sounder Local Fires Only46
Upload / Download Code46
Opto Fire and Fault Threshold Override46
Abnormal Comm's Detection47
Fast Automatics47
Pulse Buzzer on Disables47
Reset Screen47
Sounder 1 & Sounder 248
Terminology48
Test Fires Activate Fault Relay48
Networking49
Introduction49
Cable Types50
Configurations50
Ancillary Devices54
Detection54
Call Points54
Sounders54
Input/Output Devices54
Zone Monitoring Units56
Fan Controller FC6/FC1856
CFC 301 Technical I/O Unit - (Legacy Device)56
Smoke Control57
Mcom-Fc58
Way Sounder Control Unit (MPU 424/CSC354CPR)58
Mardf658
Spur Isolator- MSI85058
Beam Detector MAB50/100R58
Repeater Protocol Devices59
Repeater Panels59
LED Repeater & Graphical MIMIC Relay Board (CIOP4/8)60
Ciop727362
Touch Screen Repeater63
Getting Started & Fault Diagnosis64
Powering the Panel64
Panel Takes a Long Time to Start the Boot up Sequence after a Watchdog Reset (or Power Up)64
Power LED Not Illuminated64
Power LED on but Touch Screen Is Not Illuminated65
Power LED and Touch Screen Illuminated but no Text Visible65
Screen Is Visible, but Touch Screen Does Not Respond to Touch65
The Touch Screen Works and Is Correctly Calibrated, but I Cannot Get to the Supervisor Entry Screen65
The General Disabled LED Is Illuminated65
Commissioning66
Loop Checking with a Multimeter66
Auto-Learn Function66
Problems67
Dual Address67
The Panel Goes into Fire Straight after Auto-Learn68
The Panel Constantly Resets after Auto-Learn69
Open Circuit Positive/Negative69
Short Circuit Start or End of a Loop70
Short Circuit Middle71
Fault at Address71
Earth Fault71
Sounder 1 or 2 Fault71
FRE, FPE, Fault Relay Fault72
The Panel Fails to Auto-Learn Past a Device72
Locating a Fault on a Loop72
Other Faults73
Charger Fault73
Battery Fault73
Mains Fault73
Error Codes73
Programming Issues74
Program Updates75
Site Installer - Upload Firmware77
Panel Comm78
Download Analogue Levels and Log to PC79
Cf1100/1200 Cpd Psu83
Annex 185
Notes on CF200085
Supported Devices86
Detection86
Call Points86
Sounders86
Input/Output Devices87
Zone Monitoring Units88
Way Sounder Control Unit (MPU 424/CSC354CPR)88
Mardf689
Spur Isolator- MSI85089
Beam Detector MAB50/100R89
Repeaters89
Menu Structure90
Panel User Menu 221491
Panel Engineers Menu 213292
Other Information93
End of Document94

Eaton CF2000 - Application Guide Manual

Table of Contents

Other manuals for Eaton CF2000

Related product manuals