EDAN INSTRUMENTS CADENCE II User Manual (English)

Questions and Answers:

N
nicholsontyroneAug 21, 2025
What to do if EDAN INSTRUMENTS CADENCE II Measuring Instruments power on, LCD has no display, and the power indicator is off, the fan doesn’t run?
- T
  Tyler WeberAug 22, 2025
  If your EDAN INSTRUMENTS Measuring Instruments exhibit these symptoms, it could be due to several causes. The fuse might be damaged, requiring a fuse replacement. Alternatively, the power supply might have failed, necessitating a power supply change. It's also possible that other parts have a short circuit; in this case, you should confirm which parts are short-circuiting.
S
Stacy MaddenAug 23, 2025
What to do if EDAN INSTRUMENTS CADENCE II Measuring Instruments power on, the power is normal but no display, or improper flashes?
- G
  Gabriel ManningAug 23, 2025
  If your EDAN INSTRUMENTS Measuring Instruments is powered on but the display is absent or flashing improperly, there are several potential causes: * The LCD itself might be damaged, requiring replacement. * There could be a bad connection to the LCD, necessitating repair or replacement of the connection wire. * The mainboard could be damaged, requiring replacement. * The interface board might be damaged, also requiring replacement.
M
Mr. Michael WilliamsAug 25, 2025
What to do if EDAN INSTRUMENTS CADENCE II Measuring Instruments has faculative down?
- J
  John WrightAug 25, 2025
  If your EDAN INSTRUMENTS Measuring Instruments experiences intermittent shutdowns, it could stem from several factors. Strong interference from electrified wire netting might be the cause, suggesting a check of the power supply and earth system. Alternatively, it could be due to bad power supply or mainboard performance, indicating the need to change the power supply or mainboard, respectively. A faulty connection between the power supply, mainboard, or display could also be the culprit, pointing to the need to change or repair the connector.
P
Philip SmithAug 26, 2025
Why EDAN INSTRUMENTS Measuring Instruments network does not work?
- J
  Jared HernandezAug 27, 2025
  If the network function of your EDAN INSTRUMENTS Measuring Instruments is not working, this could be due to a network failure or a mainboard failure. You should check and repair the network cable. If the issue persists, consider changing the mainboard.
R
Rachel NashAug 27, 2025
What to do if EDAN INSTRUMENTS CADENCE II button is disabled?
- D
  David ThompsonAug 28, 2025
  If a button on your EDAN INSTRUMENTS Measuring Instruments is disabled, it might be due to a damaged keyboard, requiring a keyboard replacement. Alternatively, the keyboard connection might have a failure, suggesting the need to change or repair the keyboard wire.
T
torresjudyAug 29, 2025
What to do if EDAN INSTRUMENTS Measuring Instruments fuse burns when power on?
- H
  hubbardseanAug 29, 2025
  If the fuse in your EDAN INSTRUMENTS Measuring Instruments burns out immediately upon powering on, it suggests a short circuit within the power supply or other components. To resolve this, remove a part load and check again to isolate the issue.
M
Mark HancockAug 31, 2025
Why EDAN INSTRUMENTS CADENCE II Measuring Instruments has inaccurate measurement value?
- N
  Nicole JimenezAug 31, 2025
  If your EDAN INSTRUMENTS Measuring Instruments is displaying inaccurate measurement values, it could be due to a failure in the mainboard or the transducer. Consider changing the mainboard or the transducer.
D
David ReedSep 1, 2025
What to do if EDAN INSTRUMENTS CADENCE II Measuring Instruments power on, LCD has no display, but the power indicator is on, and the fan runs normally?
- T
  Tara WatsonSep 1, 2025
  If your EDAN INSTRUMENTS Measuring Instruments shows no display on the LCD but the power indicator is on and the fan runs normally, the issue might stem from a mainboard or connector failure. Confirm if the display is failing. Also, check the interface board and the connector.
M
Michelle JohnsonSep 3, 2025
What to do if EDAN INSTRUMENTS Measuring Instruments recorder does not work?
- Z
  Zachary CrossSep 3, 2025
  If the recorder on your EDAN INSTRUMENTS Measuring Instruments is not functioning, it could be due to the recorder being out of paper or a paper jam; in such cases, feed paper or remove the paper jam. Alternatively, there may be a recorder failure, requiring a recorder replacement. Finally, the recorder connection might have a failure, suggesting a change or repair of the recorder connecting.
J
Joshua WeeksSep 4, 2025
What to do if EDAN INSTRUMENTS CADENCE II has hoarse sound or no sound?
- A
  Amy LeeSep 4, 2025
  If your EDAN INSTRUMENTS Measuring Instruments is producing a hoarse sound or no sound at all, it could be due to a mainboard failure, requiring a mainboard replacement. Alternatively, the loudspeaker or its wiring might have a failure, suggesting a change of the loudspeaker or cable.

EDAN INSTRUMENTS CADENCE II Specifications

General

Brand	EDAN INSTRUMENTS
Model	CADENCE II
Category	Measuring Instruments
Language	English

EDAN INSTRUMENTS CADENCE II User Manual

Table of Contents

Questions and Answers:

EDAN INSTRUMENTS CADENCE II Specifications