Emerson Branson LPX - Page 33

88 pages

To Next Page

To Previous Page

100-412-196 REV. 06 23

Chapter 3: Delivery and Handling

3.1 Delivery and Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Main Page

Default Chapter5
- Table of Contents5
Chapter 1:Safety And Support11
Safety Requirements and Warnings12
- Figure 1.1 Safety Label Found on the Back of the LPX Power Supply13
General Precautions14
Chapter 5:Installation And Setup15
Chapter 6:Operation15
Regulatory Compliance16
Warranty Statement, Disclaimer17
- Table 1.1 Warranty Period17
How to Contact Branson19
Returning Equipment for Repair20
- Table 1.2 Branson Contacts22
Obtaining Replacement Parts23
Chapter 2:Introduction25
- Principle of Operation26
- Front Panel Controls and Indicators27
- Figure 2.2 Front-Panel Controls27
- Table 2.1 Front Panel Controls and Indicators28
- Table 2.2 LCD Icons30
- Back Panel Connections32
- Figure 2.3 Back Panel of LPX Power Supply32
- Table 2.3 Connections to the LPX Power Supply32
Chapter 3 3:Delivery and Handling34
Chapter 4 4:Technical Specifications36
- Table 4.1 Environmental Specifications36
- Table 4.2 Input Voltage36
- Table 4.3 Current Rating Fusing36
- Table 4.4 Maximum Power Limit37
- Table 4.5 Dimensions and Weight37
- Figure 4.1 Declaration of Conformity38
- System Performance Benchmark39
- Table 4.6 System Performance Benchmark39
- Branson Power Supply Setup Form40
Chapter 5:Installation And Setup41
Installation Checklist42
System Component Description43
- Figure 2.1 LPX Power Supply43
- Table 5.1 20 Khz LPX Power Supply Converter Compatibility43
- Table 5.2 30 Khz LPX Power Supply Converter Compatibility44
- Table 5.3 40 Khz LPX Power Supply Converter Compatibility44
- Table 5.4 LPX Power Supply Converter Part Numbers45
- Table 5.5 Start Cable Part Numbers45
- Table 5.6 RF Cable Part Numbers46
- Table 5.7 Handheld Welder Part Numbers46
- Table 5.8 Maximum Power/Duty Cycle47
Assembling the Equipment48
- Table 5.9 Setup Procedure48
- Table 5.10 Connecting the Horn to the Converter49
- Table 5.11 Stud Torque Values, Torque Wrench Part Numbers49
- Figure 5.1 Connecting Tip to Horn50
- Table 5.12 Connecting the Tip to the Horn50
Input Power Requirements51
Electrical Connections to Equipment52
- Table 5.13 User I/O Pin-Out (DB9F) Provided for Customer-Designed Interface53
Guards and Safety Equipment54
Chapter 6:Operation55
Front Panel Controls56
- Figure 6.1 LPX Power Supply User Interface56
System Modes57
- Table 6.1 System Modes and Description57
Main Screen Navigation58
System Configuration Registers60
- Table 6.2 Modify Registers60
- Table 6.3 Register Settings60
Operational Sequence63
- Table 6.4 Energy Mode Parameters63
- Table 6.5 Energy Mode Operational Sequence63
- Table 6.6 Time Mode Parameters67
- Table 6.7 Time Mode Operational Sequence67
- Table 6.8 Continuous Mode Parameters71
- Table 6.9 Continuous Mode Operational Sequence71
Save/Recall Weld Preset74
- Table 6.10 Saving a Weld Preset in Memory74
- Table 6.11 Recalling a Weld Preset from Memory75
Chapter 7:Maintenance77
Maintenance and Troubleshooting78
Reconditioning the Stack Interface80
- Figure 7.1 Reconditioning Stack Mating Surface80
Troubleshooting Charts83
- Figure 7.2 LPX Power Supply Interconnect Diagram85
Alarms/Errors86

Emerson Branson LPX - Page 33

Table of Contents

Related product manuals