EnGenius EP800 - Local Activity Monitoring Setup; Setting Local Activity Start Time; Setting Local Activity Stop Time

DocNo.FM0805issueAPage19
25.USINGTHELOCALACTIVITYMONITORINGFUNCTION

Upto3localactivitymonitoringperiodscanbesetonaperflatbasis,localinactivityisreportedthesameas theglobalactivity.

Localactivitymonitoringtimescanhaveanintervalassignedtothemwhichwillsplitthetimeintosmallerinactivityreportingperiods.
Theintervalisprogrammableonaperflatbasisfrom0to999minutes(0=disabled).Ifduringanactivemonitoringtimeperiodan
intervalelapseswheretherehasbeennoresidentactivitythenaninactivityalarmwillbesignalledforthatresident.Thiswillbe
repeatedforeachintervalwithinanactivemonitoringtimeperiod.

SETTINGTHELOCALACTIVITYSTARTTIME:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode9000or9002or9004(period1/2/3)followedbythekey
4.Entertheflatnumberfollowedbythekey
5.Amessagewillannouncethecurrentstarttime
6.IfthesettingisOKpresstheENDkey,orenteranewstarttime,orpressthe#keytodisablethetimeperiod
7.Pressthekeyandamessagewillannounce thenewstarttime
8.PresstheENDkeytocleartheconnection

_____________________________________________________________________________________________________________________________

SETTINGTHELOCALACTIVITYSTOPTIME:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode9001or9003or9005(period1/2/3)followedbythekey
4.Entertheflatnumberfollowedbythekey
5.Amessagewillannouncethecurrentstoptime
6.IfthesettingisOKpresstheENDkey,orenteranewstoptime
7.Pressthekeyandamessagewillannounce thenewstoptime
8.PresstheENDkeytocleartheconnection

_____________________________________________________________________________________________________________________________

SETTINGTHEACTIVITYINTERVALTIME:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode5004followedbythekey
4.Entertheflatnumberfollowedbythekey
5.Amessagewillannouncethecurrentintervalinminutes(0=disabled)
6.IfthesettingisOKpresstheENDkey,orenteranewintervaltimeinminutes
7.Pressthekeyandamessagewillannounce thenewintervaltime
8.PresstheENDkeytocleartheconnection

_____________________________________________________________________________________________________________________________

ENABLETIMEDACTIVITYMODE:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode3005followedbythekey
4.PresstheENDkeytocleartheconnection

IMPORTANT:youmust“EnableTimedActivityMode”forthelocalactivitymonitoringtimestotakeeffect.
_____________________________________________________________________________________________________________________________

LISTLOCALACTIVITYSETTINGS:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode9006followedbythekey
4.Enteraflatnumberfollowedbythekey
5.Localactivityperiods1‐3enabled/disabledfollowedbytheintervalsettingwillbeheard intheearpiece
6.PresstheENDkeytocleartheconnection

_____________________________________________________________________________________________________________________________




START
STOP
40MIN