EnGenius EP800 - Selecting the Operating Mode; Mode Selection via Cordless Handset; Mode Selection via Managers Panel

DocNo.FM0805issueAPage9
10.SELECTINGTHEOPERATINGMODE

TheAdventxtwardencallsystemcanreportcallsinthreedifferentways;

1. ONSITEMODE‐toanonsitecarerviaacordlesshandset

2. LOCALOFFSITEMODE‐toamobilecarerviaamobiletelephone

3. REMOTEOFFSITEMODE‐to24hourcontrolcentreviathetelephoneline

TheoperatingmodeisselectedviaakeyswitchontheStatusModule,byentering
specialcodesonthecordlesshandsetorfromtheoptionalManager’sPanel.
______________________________________________________________________________________________________________

MODESELECTIONUSINGTHESTATUSMODULE:

TheStatusModuleisusuallywallmountedintheManagersoffice.











______________________________________________________________________________________________________________

MODESELECTIONUSINGTHECORDLESSHANDSET:

1.PresstheTALKkeyandenter81
2.Waitforthe“Ready”promptintheearpiece
3.Enterthecode1004followedbythekey
4.Thecurrentoperatingmodewillbeannounced
5.Waitforthe“Ready”promptintheearpiece
6.PresstheENDkeytomaintainthecurrentoperatingmodeor
Enteroneofthefollowingcodestoselectanewoperatingmode;
1005forOnsiteMode,1006forLocalOffsiteModeor1007forRemoteOffsiteMode
7.Pressthekeyandthenewoperatingmodewillbeannounced
8.PresstheENDkeytocleartheconnection

______________________________________________________________________________________________________________

MODESELECTIONUSINGTHEMANAGER’SPANEL:



1.Touchthe“SystemPanel”tabalongthetopofthescreen
2.ThecurrentoperatingmodewillbeGREEN
3.Touchtherequiredoperatingmodebuttononthescreen
4.YouwillbepromptedforaPasswordtochangetheoperatingmode
5.EnterthePassword(default:1234)
thentouchthe“Logon”button
6.ThenewoperatingmodewillbeGREEN


______________________________________________________________________________________________________________




Ifthesystemisoperatinginonsitemodeandanalarmcallremainsun‐answeredforapresettime(6minutes)the
callwillautomaticallyswitchtolocaloffsitemodeandreportthecalltoamobilewarden.Ifthecallstillgoes
un‐answeredthenremoteoffsitemodewillbe
selectedandthecallwillgotoa24hourcontrolcentre.

Itisnotpossibletoselectlocaloffsiteorremoteoffsitemodeifatelephonelinefaultexists.Ifthesystemis
operatingineitherofthesemodeswhenatelephonelinefaultdevelopsthenthesystemwillreportcallstothe
onsitemanager.Callswillgobacktotheselected
offsitemodeassoonasthefaultclears.

Atelephonelinefaultisreportedonthecordlesshandset,theStatusModuleandaBTlinefaultbeacon(iffitted).


1.Turnthekeyswitchtoselectthedesiredoperatingmode.
2.ChecktherelevantYELLOWOPERATINGMODElightislit.
3.Removethekeyfromtheswitch.

Theoperatingmodecannotbechangedwhen theGREENCALLINPROGRESSlightislit.
Waituntilthecallhasendedbeforeturningthekey.

TheREDFAULTSEXISTlightwillbelitiffaults arestoredinthesystemmemory.
Seesection13forhowtocheckthefaultmemory.

Thetime&dateofallsystemeventscanberecordedonanoptionalprinter.
Onsite
Mode
Optional
Printer