ENTR Dead Bolt - User Manual

46 pages

Save Page as PDF

To Next Page

ENTR® Dead Bolt User Manual

Table of Content

1. Cylinder Installaon 5

1.1 Package Content 5

1.2 Tools Requirements 5

1.3 Prior to Installaon 6

1.4 Cylinder & Unit Installaon 6

1.5 Magnet Fing 8

2. ENTR® Descripon 9

2.1 ENTR® Descripon 9

2.2 Indicaons 9

2.3 ON/OFF Switch 10

2.3.1 Switching the ENTR® ON 10

2.3.2 Switching the ENTR® OFF 10

2.3.3 Low Baery Indicaon 10

2.4 Iniang the Lock 11

2.5 Default PIN Code 11

3. Operaon 12

3.1 Changing PIN Code 12

3.2 Door Conguraon 13

3.3 Pairing Remote Control 16

3.4 Deleng Remote Control 17

3.5 Seng the Sound Signal 18

3.6 Seng Locking Mode 19

3.7 Operated by Knob 20

3.8 Operated by Slide Buons 20

Main Page

Questions and Answers

L
Levi BradshawSep 7, 2025
What to do if I get an error sound at the end of Step 1 of the ENTR Dead Bolt configuration?
- K
  katelynrobinsonSep 7, 2025
  Verify that you are able to lock and unlock the door using the key without issue.
S
Samantha GilbertAug 22, 2025
What to do if my ENTR Door locks touch panel isn't responding?
- J
  Jenna CraigAug 22, 2025
  If the touch panel on your ENTR Door locks isn't responding as expected, turn the door unit off and wait for 3 seconds. When turning the power back on, avoid touching the front panel until the unit beeps.
S
Suzanne KennedySep 4, 2025
What to do if I get an error sound when starting the ENTR Door locks configuration process?
- M
  Michael HammondSep 4, 2025
  This could mean that the factory code hasn't been replaced with your administrative code. Go back and set your administrative code for your ENTR Door locks.
C
Charles Lloyd MDSep 3, 2025
What to do if I've configured my ENTR Dead Bolt Door locks, but the lock/unlock actions are reversed?
- J
  John ThompsonSep 3, 2025
  Redo the configuration process for your ENTR Door locks, paying attention to the door's orientation (Left= 1 and Right = 3).
P
pwilliamsSep 2, 2025
How to fix ENTR Dead Bolt Door locks when the knob isn't unlocking?
- J
  Jose BeckerSep 2, 2025
  Make sure that the mechanical key can operate the lock and that the electronic unit is properly attached to the cylinder.
J
Jenna AndersonAug 31, 2025
What to do if I'm having trouble pairing the wall reader with my ENTR Door locks?
- L
  Lori JohnsonSep 1, 2025
  Set the door unit to pair mode, by pressing Add+Code+1, then immediately set the wall reader to pair mode. You'll have a 30 second window until the door unit reverts back to standby mode.
J
John ContrerasAug 30, 2025
What to do if my ENTR Dead Bolt touchpad isn't accepting the PIN code?
- X
  xcopelandAug 30, 2025
  This specific code already exists within the device's memory. Make sure that the PIN code is 4 - 10 digits.
M
Mrs. Katrina EvansAug 29, 2025
What to do if my ENTR Door locks isn't accepting the administrative code?
- J
  Jacob AguirreAug 29, 2025
  Make sure the code you are using contains between 4 and 10 digits and is different from the "12345" factory code.
B
Bradley YatesAug 27, 2025
What to do if my ENTR Dead Bolt Door locks wall reader's blue LED is blinking but the door unit isn't responding?
- J
  jsmithAug 27, 2025
  Verify that the wall reader is paired to the door unit by redoing the pairing process. You should hear double beeps from both devices when pairing is completed.
H
heathersanchezAug 27, 2025
What to do if I can't pair my ENTR Dead Bolt remote control?
- J
  James PottsAug 27, 2025
  If you're having trouble pairing the remote control with your ENTR Door locks: * Confirm that the LED on the remote control is ON when you press the button. * Repeat the pairing process again while standing closer to the door unit.