Extron electronics XTP II CrossPoint 6400 User Manual

SIS Command and Response Table for Advanced Matrix Switcher Commands (continued)
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Save and directly write global presets
Save current configuration as a
global preset
X#
, Spr
X#]
Command character is a comma.
Example:
8,
Spr08
]
Save current ties as preset 8.
Direct write process —
NOTE: The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number,
as shown below. In a directly-written preset, the input for each output position (or no tied input) remains unchanged unless overwritten
or cleared.
If you do not clear the ties in a global preset number before you directly write a global preset to that number, ties that are part of the
previous version of the specified preset with the same number can unexpectedly become part of the newly-created preset.
Clear global preset ties
E
+
X#
P0*!
}
Spr
X#]
Clear all ties in preset
X#
.
Directly write a global preset
E
+
X#
P
X!
*
X@
!
X!
*
X@
%
X!
*
X@
$ ...
X!
*
X@
&
}
Enter as many ties as are valid. The tie
all (
!), tie RGB (&), tie video (%), and
tie audio (
$) commands are all valid.
Spr
X#]
Example:
E
+27P0*!
}
Spr27
]
Clear all ties in preset 27.
Esc
+27P12*5!10*09%3*2$3*8&
Brackets are shown to separate ties for
clarity only. Create global preset 27,
which ties video and audio input 12 to
output 5, video input 10 to output 9,
audio input 3 to output 2, and video
input 3 to output 8.
Spr27
]
Resets
Reset global presets and names
E
ZG
}
Zpg
]
Clear all global presets and their names.
Reset one global preset
EX#
ZG
}
Zpg
X#]
Clear global preset
X#
.
Reset audio input levels
E
ZA
}
Zpa
]
Reset all audio input levels (gain and
attenuation) to 0 dB.
Reset audio output levels
E
ZV
}
Zpv
]
Reset all audio output levels (volume)
to 100% (no attenuation).
Reset whole switcher
E
ZXXX
}
Zpx
]
Clear all ties and presets, reset all audio
gains to 0 dB, and reset volume to 100%.
NOTE: The reset whole switcher (
E
ZXXX
}
) command resets not only the switcher, but any connected endpoints.
Absolute reset, including IP settings
E
ZQQQ
}
Zpq
]
Similar to Reset whole switcher, plus
clear the IP address to 192.168.254.254
and subnet mask to 255.255.000.000.
NOTE: The absolute reset (
E
ZQQQ
}
) command resets not only the switcher, but any connected endpoints.
Absolute reset, excluding IP settings
E
ZY
}
Zpy
]
Similar to Absolute reset, including
IP settings (
E
ZQQQ
}
), but excludes
the following IP settings: IP address,
subnet mask, gateway address,
unit name, DHCP setting, and port
mapping (telnet, Web, and direct
address).
NOTES: The absolute reset (
E
ZY
}
) command:
• Preserves communications with the device and is recommended after a firmware update.
• Resets not only the switcher, but any connected endpoints.
NOTE: X! = Input number 00 – 16, 32, or 64 (00 = untied)
X@ = Output number 01 – 16, 32, or 64
X# =
Global preset number
00 – 32 (00 = current configuration, applies to view ties command only)
XTP II CrossPoint 1600, 3200, and 6400 Switchers • Programming Guide 111

Extron electronics XTP II CrossPoint 6400 Specifications

General

Brand	Extron electronics
Model	XTP II CrossPoint 6400
Category	Matrix Switcher
Language	English