Extron electronics XTP II CrossPoint 6400

To Next Page

To Previous Page

Figure 86. Button Label Blanks

XTP II CrossPoint 1600, 3200, and 6400 Switchers • Maintenance and Modifications 153

Main Page

Table of Contents7
Introduction9
About this Guide9
About the XTP II Crosspoint Switchers10
Endpoint Configuration11
Input and Output Boards and Signal Types12
Features15
Installation18
Setup and Installation Checklist18
Rear Panel Cabling and Features19
Input and Output Boards22
Remote Control Ports35
Ethernet Connection35
Reset Button and LED36
Power36
Front Panel Configuration Port and Power Leds37
Operation38
Front Panel Controls and Indicators38
Input and Output Buttons41
Control Buttons42
I/O Controls44
Power Leds44
Button Icons45
Front Panel Operations45
Definitions46
Power46
Front Panel Security Lockouts46
Creating a Configuration47
Viewing the Configuration52
Using Presets55
Muting and Unmuting Video and Audio Outputs57
Viewing and Adjusting the Input Audio Level59
Viewing and Adjusting the Analog Output Volume65
Setting the Front Panel Locks (Executive Modes)70
Performing a System Reset from the Front Panel71
Background Illumination72
Selecting the Rear Panel Remote Port Protocol and Baud Rate72
Rear Panel Operations73
Performing a Hard Reset (Reset 1)75
Performing Soft System Resets (Resets 3, 4, and 5)76
Optimizing the Analog Audio77
Troubleshooting77
Configuration Worksheets78
Worksheet Example 1: System Equipment78
Worksheet Example 2: Daily Configuration79
Worksheet Example 3: Test Configuration80
XTP II Crosspoint 6400 Switchers Configuration Worksheet81
XTP II Crosspoint 3200 Switchers Configuration Worksheet82
XTP II Crosspoint 1600 Switchers Configuration Worksheet83
Programming Guide84
Local Host-Control Ports85
Ethernet (LAN) Port85
Default IP Addresses85
Establishing a Connection86
Connection Timeouts86
Number of Connections86
Using Verbose Mode86
Host-To-Switcher Instructions87
Switcher-Initiated Messages87
Switcher Error Responses88
Using the Command and Response Tables88
SIS Command and Response Table for Basic Matrix Switcher Commands94
SIS Command and Response Table for Input-Board-Specific Commands95
SIS Command and Response Table for Input-Endpoint-Specific Commands103
SIS Command and Response Table for Output-Board-Specific Commands110
SIS Command and Response Table for Output-Endpoint-Specific Commands114
SIS Command and Response Table for Advanced Matrix Switcher Commands118
SIS Command and Response Table for IP- and Remote Port-Specific Commands125
Special Characters126
HTML Operation127
Download the Startup Page128
Status Tab129
System Status Page129
DSVP Page130
HDCP Page131
Configuration Tab132
System Settings Page132
Passwords Page135
Email Settings Page136
Firmware Upgrade Page138
File Management Tab142
File Management Page142
Control Tab143
Set and View Ties Page143
Input Adjustments Page144
Output Adjustments Page145
EDID Configuration Page148
XTP Power Page149
Global Presets Page150
Maintenance and Modifications151
Mounting the Switcher151
UL Guidelines151
Mounting Instructions152
Battery and Power Precautions152
Removing and Installing an Input or Output Board or Blank Panel152
Removing an Input or Output Board or Blank Panel152
Installing an Input or Output Board or Blank Panel153
Removing and Installing a Power Supply Assembly (XTP II Crosspoint 6400)154
Removing a Power Supply Assembly154
Installing a Power Supply Assembly154
Replacing and Terminating the Power Cable (XTP II Crosspoint 6400)155
Replacing the Cable155
Replacing or Installing the Power Plug158
Removing and Installing Button Labels158
Making Labels Using the Button-Label Generator Program158
Making Labels from Paper Templates160
Installing Labels in the Buttons160
Ethernet Connection162
Ethernet Link162
Default IP Address162
Pinging to Determine the Extron IP Address163
Pinging to Determine the Web IP Address163
Configuring the XTP II Crosspoint Switcher for Network Use Via the ARP Command164
Connecting as a Telnet Client165
Telnet Tips165
Subnetting - a Primer167
Gateways167
Analog and Remote Devices167
IP Addresses and Octets167
Subnet Masks and Octets168
Determining Whether Devices Are on the same Subnet168

Extron electronics XTP II CrossPoint 6400 - Page 161

Table of Contents

Other manuals for Extron electronics XTP II CrossPoint 6400

Related product manuals