Need help?Do you have a question about the Fermator VF7 and is the answer not in the manual?
General| Brand | Fermator |
|---|---|
| Model | VF7 |
| Category | Control Unit |
| Language | English |
Identifies the product as the VF7 Electronic Module for automatic horizontal sliding car doors.
Details the connections for power supply and the motor, including voltage inputs.
Illustrates the various input and output terminals for signals and power on the VF7 module.
Specifies the main supply voltage (230 VAC) and frequency requirements for the VF7 module.
Explains external and internal voltage inputs for open, close, common, and 0V signals.
Details the open signal input and the serial communication port for external devices.
Describes priority inputs like Re-open, Light Curtain, and the +12V output for activation.
Explains inputs for bypass contact, slow closing, and floor level emergency power.
Details output relays and LEDs for door status: Open, Closed, Photocell, Obstruction, Light Curtain, Temperature.
Details the encoder input for position/speed and the motor output for speed/torque control.
Outlines the main objectives and navigation of the VF7 graphic interface for monitoring and configuration.
Displays the last five activated alarms, allowing users to view and acknowledge them.
Details common alarms like Short-C, Current, Low Volt, Memory, Friction, Belt, Encoder, with causes and solutions.
Covers alarms related to obstructions, calibration failures, and motor/module temperature issues.
Details temperature-related alarms and referencing issues, including their resolution.
Explains how to navigate the Monitor Menu to view real-time VF7 parameters.
Lists categories like Parameters, Outputs, Counters, Motor, Inputs, and Information for monitoring.
Provides specific parameters for monitoring door status, position, speed, voltage, and motor temperature.
Details monitoring of input/output signals, status, and counter values for door operations.
Details door cycle counts, power-ups, errors, and system information like software/hardware versions.
Introduces the Programming Menu for modifying VF7 internal parameters and options.
Covers basic options, interact settings, input logic, functions, and parameter groups like speeds and lengths.
Provides a step-by-step guide on how to select, modify, and save parameter values.
Configures door model (T1-C8), control mode (Master/Slave), and landing door type (Automatic/Semiautomatic).
Explains how to configure single or dual input modes for door control signals.
Configures priority inputs, keyboard shortcuts, and specific signal behaviors like slow close and bypass.
Details options for door anticipation, bypass signals, curtain error handling, and DPM system.
Configuration for normally closed (NC) contacts for various input signals like Open, Close, and Curtain.
Sets up Eco Mode, CDL, Security Device, Barrier Timer, Temperature, Energy Limit, and other advanced functions.
Visual representation of open and close speed profiles, illustrating key speed and length parameters.
Details parameters for door mass, clutch mass, gear ratio, and various opening/closing speeds and accelerations.
Explains the one-time motor calibration process to detect electrical characteristics for optimal performance.
Defines parameters for door lengths, torques (open, close, hold), and time delays (Eco, Backstep).
Details how to perform a test cycle and the crucial door learning/autoadjustment process.
Allows configuration of language, display, factory settings, and password protection for the VF7.
Details essential connections like motor, encoder, photocell, and power supply for initial setup.
Guides on programming door type, landing type, rotation sense, control behavior, and connecting cables.
Explains the anti-banging system and electronic car door lock features for power failure scenarios.
Details how the electronic car door lock operates during power failures and can be enabled/disabled.
Outlines requirements for kinetic energy, door model, and light curtain settings to meet EN 81-20/50 standards.
Explains kinetic energy limits and how overheating protection is managed via temperature measurement.
Provides technical specifications for power supply, inverter, inputs, and positional control.
Details switched contacts, contact rating, switch time, output current, and voltage.
Provides moving mass data and multiplier factors for the Compact product line based on panel type and fire homologation.
Lists multiplier factors for the 40/10 product line based on differences in model, opening, and panel specifications.
Provides multiplier factors for the Premium product line for various configuration differences.
Lists moving mass and multiplier factors for the Platinum product line.
Demonstrates calculation of moving mass increment based on PL and HL changes for the 40/10 PM model.
Shows calculation of moving mass involving opening, panel count, PL, and HL differences for Premium PM.
Declares that the VF7 Electronic Module conforms to relevant EU directives and standards.
Advises on modifications, liability for incorrect installation, and the right to change specifications.
To Next Page
