Ferroli ECOTRONIC Plus - Bus; Mains Supply

7 |
ECOTRONIC Plus
© Ferroli 08164 ECOTRONIC Plus.monen.indd
De ltaS ol M
Main menu
Meas. values
Reports
Solar
GND
S1
S2
S3
S4
S5
S7
S6
S8
S9
S10
S11
S12
----
CS10
Imp1
Imp2
Bus
VBus
RS232
Sensors
R9-A
R9-M
R9-R
DeltaSol M
LN
R8-A
R8-R
R7-A
R7-R
R6-A
R6-R
R5-A
R5-R
R4-A
R3-A
R2-A
R1-A
floating re la ye lectr omechanic re la y semi-conductor r ela y
Schutzleiter -Sammelklemmenblock benutzen
Nullleiter -Sammelklemmenblock benutzen
N
Use the PE Collectiv eT erminal Block
Use the Neutral Conductor Collecti ve T erminal Block
N
Masse-Sammelklemmenblock ben utzen
Use the Gr ound Collectiv eT erminal Bloc k
T6,3A
Netz / Mains
220...240 V~
V or Öffnen der Klemmenabdeckung
Gerät spannungslos schalten
Isolate mains befor e re moving clamp-co ve r
6,3 (1) A 220 ... 240 V~
GND
PE
L
N
PE
N
®
®
Netz / Mains
220 ... 240 V~
1.2.5 Mains supply
The power supply to the controller must be carried out via
an external power switch (last step!) and the supply voltage
must be 220 ... 240 V~ (50 ... 60 Hz). Flexible cables must be
attached to the housing with the enclosed strain relief and the
corresponding screws or be run into the controller housing
in a cable conduit or trunking (see advice on page 4).
Mains connection :
1 = protective conductor (common terminal block)
2 = neutral conductor N (common terminal block)
3 = conductor L
De ltaS ol M
Main menu
Meas. values
Reports
Solar
GND
S1
S2
S3
S4
S5
S7
S6
S8
S9
S10
S11
S12
----
CS10
Imp1
Imp2
Bus
VBus
RS232
Sensors
R9-A
R9-M
R9-R
DeltaSol M
LN
R8-A
R8-R
R7-A
R7-R
R6-A
R6-R
R5-A
R5-R
R4-A
R3-A
R2-A
R1-A
floating re la y e lectr omechanic re la y semi-conductor r ela y
Schutzleiter -Sammelklemmenblock benutzen
Nullleiter -Sammelklemmenblock benutzen
N
Use the PE Collectiv eT erminal Block
Use the Neutral Conductor Collecti ve T erminal Block
N
Masse-Sammelklemmenblock ben utzen
Use the Gr ound Collectiv eT erminal Bloc k
T6,3A
Netz / Mains
220...240 V~
V or Öffnen der Klemmenabdeckung
Gerät spannungslos schalten
Isolate mains befor e re moving clamp-co ve r
6,3 (1) A 220 ... 240 V~
GND
PE
L
N
PE
N
®
®
1.2.4 Bus
The controller is equipped with two bus interfaces for data
communication:
1.) The VBus
®
for data transfer with and energy supply to
external modules. The connection is carried out at the
two terminals marked “VBus
®
“ (any polarity). One or
more VBus
®
modules can be connected via this data
bus:
 •WMZcalorimeter
 •largedisplays
 •HKM,modularheatingcircuitexpansion
2.) The RS232-interface for direct connection to a PC.
Measured values and parameters of the controller can
be read out, adjusted, processed and visualised by means
of the evaluation tool RSC (Service Center Software).
The software allows easier paramatrisation and function
control of the system.
RS232-connection
RJ45 socket
VBus
terminal