Need help?Do you have a question about the Foundry Networks FES4802-POE and is the answer not in the manual?
Overview of Foundry Networks FastIron compact switches and their capabilities.
Lists supported configurations for various FastIron compact switch models.
Describes how software versions affect device features and capabilities.
Explains Power over Ethernet capabilities and standards for specific models.
Describes IPv6 capabilities and supported models with specific software releases.
Describes physical characteristics of FES, FESX, and FWSX devices.
Describes ports and uplink options for FESX424, FESX624, and FWSX424.
Details ports and uplink options for HF models of FESX.
Describes POE capabilities and ports for the FESX424-POE model.
Details ports and uplink options for FESX448, FESX648, and FWSX448 models.
Lists the front panel control features available on each device.
Explains the function and location of the console port for management.
Describes the network interfaces available on FES2402, 4802, and 9604 models.
Describes FES 10/100/1000 Mbps ports, connectors, and fiber options.
Describes port types and interface options for FESX compact switches.
Discusses optional 10-Gigabit Ethernet modules and their supported transceivers.
Lists supported network interfaces for FastIron compact devices.
Overview of AC and DC power supplies and their compatibility.
Procedures for installing an optional second power supply for redundancy.
Instructions for installing the device on a desktop, rack, or wall.
Detailed steps for mounting the device in an equipment rack.
Procedures for powering on the installed system.
Steps to verify the device is working correctly after power-on.
Guide for connecting a PC or terminal for initial CLI configuration.
Secures CLI access by assigning passwords.
Procedure to regain access if a password is lost.
Steps to assign IP addresses for network management.
Guidelines for connecting Foundry devices to other network equipment.
Procedure for installing SFP or XFP transceivers into fiber ports.
Methods for testing network connectivity after installation.
General steps for troubleshooting network connectivity issues.
How to display and change temperature warning/shutdown levels on FES switches.
Detailed steps for replacing a power supply unit.
Step-by-step guide to removing an AC power supply.
Step-by-step guide to installing an AC power supply.
Step-by-step guide to removing a DC power supply.
Step-by-step guide to installing a DC power supply.
Procedures for installing or replacing 10-Gigabit Ethernet modules.
Steps to remove a 10-Gigabit Ethernet module.
Steps to install a 10-Gigabit Ethernet module.
Procedure for replacing the CPU DIMM on specific FESX IPv6 models.
Instructions for replacing fiber optic modules (SFP/XFP).
Steps to remove a fiber optic module from a port.
Steps to install a new fiber optic module.
Instructions for upgrading the device to Layer 3 software.
General steps and requirements for performing a Layer 3 software upgrade.
Detailed steps for installing hardware and software for Layer 3 upgrade.
Steps for installing the hardware components of the upgrade.
Instructions for installing the Layer 3 software after hardware upgrade.
General| Model | FES4802-POE |
|---|---|
| PoE Support | Yes |
| PoE Budget | 370W |
| Jumbo Frame Support | Yes |
| Manageable | Yes |
| Humidity | 10% to 90% non-condensing |
| Ports | 48 x 10/100BASE-TX, 2 x Gigabit SFP |
| MAC Address Table Size | 16, 000 entries |
| Jumbo Frame Size | 9216 bytes |
| Features | VLAN, QoS, IGMP Snooping, Port Mirroring |
| Power Supply | 100-240 VAC, 50/60 Hz |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Storage Temperature | -20°C to 70°C (-4°F to 158°F) |
| Weight | 4.5 kg (9.9 lbs) |
To Next Page
