What to do if Fronius Inverter shows invalid device type?
If your Fronius Inverter displays an invalid device type, press the ‘Enter’ key to confirm the error. If the status code persists, contact a Fronius-trained service technician.
What to do if Fronius Inverter AC voltage is too high?
If your Fronius Inverter indicates an AC voltage that's too high, first check the grid connections. If the problem continues, it's recommended to contact your system installer for further assistance.
What to do if Fronius IG-TL 4.0 AC voltage is too low?
If your Fronius Inverter displays a message indicating the AC voltage is too low, start by inspecting the grid connections. If the problem persists, contact your system installer.
What to do if Fronius IG-TL 4.0 AC frequency is too high?
If your Fronius Inverter shows that the AC frequency is too high, you should check the grid connections. If the status code keeps recurring, contact your system installer.
What to do if Fronius IG-TL 4.0 AC frequency is too low?
If the AC frequency of your Fronius Inverter is too low, check the grid connections. If the issue continues, contact your system installer.
What to do if Fronius Inverter internal component is defective?
If your Fronius Inverter indicates an internal component is defective, contact a Fronius-trained service technician.
What to do if measurement signal recording is not possible for the insulation test on Fronius IG-TL 4.0 Inverter?
If your Fronius Inverter indicates that measurement signal recording is not possible for the insulation test, and the status code persists, contact a Fronius-trained service technician.
What to do if Fronius Inverter AC polarity is inverted?
If your Fronius Inverter indicates that the AC polarity is inverted (L/N), check AC polarity (L/N). If the status code persists, contact a Fronius-trained service technician.
What to do if Fronius Inverter shows fixed voltage setting error?
If the 'fixed voltage' setting has been selected instead of MPP voltage operation and the voltage is set to a value that is too low or too high on your Fronius Inverter, remove excess solar modules so DC voltage fits within inverter limits. If the status code persists, contact a Fronius-trained service technician.
What to do if Fronius IG-TL 4.0 Inverter DC input voltage is too high?
If your Fronius Inverter shows that the DC input voltage is too high, the fault should rectify automatically. If this status code keeps recurring, contact your system installer.
Explanation of safety symbols and warnings used in the manual.
General safety rules for device operation, handling, and personnel qualifications.
Details on inverter safety features like RCMU and grid monitoring.
Defines the inverter's intended use and restrictions, including photovoltaic system stipulations.
Criteria for selecting a suitable location for the inverter, considering environmental factors.
Instructions for selecting mounting hardware and attaching the wall bracket.
Procedures for connecting the inverter to the AC grid, including terminals and cables.
Guidelines for connecting solar modules, including voltage and safety aspects.
Instructions for installing string fuses, including selection criteria and safety.
Steps for initial setup, including language and time configuration.
Information on the inverter's self-diagnostic system and status codes.
Codes indicating faults that require intervention from a trained service technician.
Detailed instructions for safely replacing string fuses in the inverter.
Detailed technical specifications for all Fronius IG TL inverter models.
General| Rated Output Power | 4.0 kW |
|---|---|
| Max. apparent AC power | 4000 VA |
| AC nominal power | 4000 W |
| AC voltage range | 180 - 280 V |
| Nominal AC voltage | 230 V |
| THD | < 3 % |
| Number of DC connections | 2 |
| Protection class | IP65 |
| Number of MPP Trackers | 2 |
| Operating Temperature Range | -25 °C to +60 °C |
| Cooling Method | Convection |
| Model | IG-TL 4.0 |
| Type | Grid-tied inverter |
To Next Page