What to do if Fronius TransPocket 5000 CEL Welding System shows Err | PE error?
If you see the error message 'Err | PE' on your Fronius Welding System, it indicates that the earth-fault current watchdog has triggered the power source’s safety cut-out. To resolve this, switch off the power source, wait for 10 seconds, and then switch it on again. If the error persists after several attempts, you should contact After Sales Service.
What to do if Fronius Welding System shows Err | bPS, Err | IP, dSP | Axx, dSP | Cxx, dSP | Exx, dSP | Sy, dSP | nSy?
If your Fronius Welding System displays 'Err | bPS, Err | IP, dSP | Axx, dSP | Cxx, dSP | Exx, dSP | Sy, dSP | nSy', it means the earth-fault current watchdog has activated the power source’s safety cut-out. Try switching off the power source, waiting 10 seconds, and then switching it back on. If the error continues after several attempts, contact After Sales Service.
What does error r | E33, r | E34 mean on Fronius TransPocket 5000 CEL?
If your Fronius Welding System displays 'r | E33' or 'r | E34', it indicates poor contact between the electrode holder or chuck for the tungsten electrode and the workpiece. Clean the point of contact, firmly clamp the electrode holder or chuck for the tungsten electrode, and press down on the workpiece. Also, check the earth connection.
What does error r | E30 mean on Fronius Welding System?
If your Fronius Welding System displays 'r | E30', it means there is no contact with the workpiece during r-Adjustment. Connect the earth cable and ensure a tight connection between the electrode holder and the workpiece.
What does error r | E31 mean on Fronius TransPocket 5000 CEL?
If your Fronius Welding System displays 'r | E31', it indicates that the r-Adjustment procedure has been interrupted by repeatedly pressing the Setup / Store button. Ensure a tight connection between the electrode holder or chuck for the tungsten electrode and the workpiece, then press the Setup / Store button.
Why is there no shielding gas in my Fronius TransPocket 5000 CEL?
If your Fronius Welding System isn't providing shielding gas, there are several possible causes. The gas cylinder might be empty, so you should change it. The gas pressure regulator could be faulty, requiring replacement. The gas hose may not be mounted correctly or could be damaged, so mount or change it. Lastly, the TIG gas-valve welding torch might be defective, in which case you should replace it.
How to troubleshoot poor welding properties in Fronius TransPocket 5000 CEL Welding System?
If your Fronius Welding System is showing poor welding properties, make sure to check your settings, as the welding parameters might be wrong. Also, ensure good contact to the workpiece to avoid a poor earth connection. Check the pressure regulator, gas hose, gas solenoid valve, and torch gas connection to make sure you have enough shielding gas. Finally, if the welding torch is leaking, change the torch.
Why Fronius TransPocket 5000 CEL Welding System power source does not function?
If your Fronius Welding System's power source does not function, check the mains supply lead and ensure the mains plug is properly plugged in. Also, inspect the mains fuse and change it if it's faulty. Finally, check the mains outlet socket or plug and replace any faulty components.
What to do if Fronius Welding System shows over-temperature in primary circuit?
If your Fronius Welding System indicates an over-temperature in the primary circuit of the power source, allow the power source to cool down.
What to do if Fronius Welding System shows over-temperature in secondary circuit?
If your Fronius Welding System indicates an over-temperature in the secondary circuit of the power source, allow the power source to cool down.
General| Brand | Fronius |
|---|---|
| Model | TransPocket 5000 CEL |
| Category | Welding System |
| Language | English |
Explains the meaning of various safety symbols (Danger, Warning, Caution, Note).
Covers general safety, operator, and personnel obligations.
Highlights risks like mains connection, personal protection, and general hazards.
Emphasizes safety and outlines steps required before starting MMA welding.
Highlights safety precautions and steps for starting and performing TIG welding.
Lists common error codes, their causes, and remedies.
To Next Page
