Fuji Electric RYS201S3-VVS - Torque Command Gain, Offset; Output Torque; Torque Limiting

MHT258a (Engl.)5-32
System parameter 61
Para. Name Setting range Initial value Change
61 Speed limit changeover 0 : Basic para. 16
1: Speed command [NREF]
0 Power
*Maximum speed at +10V
・Torque command filter
Torque control voltage can be changed by a filter time constant concerning torque command voltage [TREF] by setting basic para. 43.
Basic parameter 43
Para. Name Setting range Initial value Change
43 Torque command filter 0.0 to 9.9s (in 0.1s steps) 0 Always
・Torque command gain, offset
The input gain or offset to torque command [TREF] terminal can be adjusted by system para. 65 or 66.
System parameter 65
Para. Name Setting range Initial value Change
65 Torque command gain ±0.10 to ±1.50 (in 0.01 steps) 1.00 Always
System parameter 66
Para. Name Setting range Initial value Change
66 Torque command offset –200 to +200 (in increment of 1) (Individval) Always
・Output torque
There is an output torque dispersion of approximately ±10% between indiviclual motors.
If the output torque is the rated torque or lower, a continuous running is available.
・Torque limiting
Output torque can be limited by basic para.59. Maximum torque limit value is always effective.
Basic parameter 59
Para. Name Setting range Initial value Change
59 Maximum torque limiting 0 to Max. torque [%] (in increment of 1) 300 Always
K80791234
K80791234K80791234
K80791234
L1
L1L1
L1
L2
L2L2
L2
L3
L3L3
L3
DB
DBDB
DB
P1
P1P1
P1
N
NN
N
P+
P+P+
P+
U
UU
U
V
VV
V
W
WW
W
CHARGE
CHARGECHARGE
CHARGE
FALDIC
FALDICFALDIC
FALDIC
SHIFT
SHIFTSHIFT
SHIFT
ENT
ENTENT
ENT
RYS201S3-VVS
RYS201S3-VVSRYS201S3-VVS
RYS201S3-VVS
MODE
MODEMODE
MODE
ESC
ESCESC
ESC
K80791234
K80791234K80791234
K80791234
L1
L1L1
L1
L2
L2L2
L2
L3
L3L3
L3
DB
DBDB
DB
P1
P1P1
P1
N
NN
N
P+
P+P+
P+
U
UU
U
V
VV
V
W
WW
W
CHARGE
CHARGECHARGE
CHARGE
FALDIC
FALDICFALDIC
FALDIC
SHIFT
SHIFTSHIFT
SHIFT
ENT
ENTENT
ENT
RYS201S3-VVS
RYS201S3-VVSRYS201S3-VVS
RYS201S3-VVS
MODE
MODEMODE
MODE
ESC
ESCESC
ESC
Torque command [TREF] terminal
Torque command gain : System para. 65
Torque command offset : System para. 66
Torque command filter : Basic para. 43
Speed command [NREF] terminal
Speed command gain : System para. 63
Speed command offset : System para. 64
Max. torque limiting : Basic para. 59
(Always valid)
Max. speed : Basic para. 16
Speed limit changeover : System para. 16
0 : Basic para. 16
1 : Speed command [NREF]