EasyManuals Logo

Fuji Xerox ApeosPort-IV C3375 Administration Guide

Fuji Xerox ApeosPort-IV C3375
731 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #562 background imageLoading...
Page #562 background image
15 Problem Solving
562
Problem Solving
15
116-710
[Cause] The correct document size could not be judged because the receive data exceeded the
HP-GL/2 (optional) spool size.
[Remedy] Increase the size assigned to HP-GL/2 auto layout memory.
116-713
[Cause] The data has been divided into a number of jobs because of insufficient disk space.
[Remedy] Delete unnecessary data from the hard disk to free up disk space.
116-714
[Cause] An HP-GL/2 (optional) command error occurred.
[Remedy] Check the print data.
116-716
116-717
[Cause] An error occurred when reading the data on the media.
[Remedy] On a computer, confirm the content recorded on the media.
116-720
[Cause] An error occurred during print processing because of insufficient memory.
[Remedy] Stop unnecessary ports or delete unnecessary data to free up disk space.
116-725
[Cause] Failed to write the image log because the image log storage area on the machine is
insufficient.
[Remedy] Execute the operation again.
If this error still is not resolved, take one of the following measures:
z
Delete unnecessary image logs.
z
Change the [Assurance Level] setting for image logs to [Low].
In this case, selecting [Low] does not secure the contents of created image logs.
116-738
[Cause] The size and orientation of the form specified are not matched with the paper to be
printed.
[Remedy] Match the size and orientation of the paper with the form specified, and print again.
116-739
[Cause] The form or logo data cannot be registered because memory for the form and logo data
or memory capacity for the hard disk is insufficient.
[Remedy] Delete unnecessary data, or free up the space for the form memory.
116-740
[Cause] A numerical value operation error occurred because a value exceeding the value limit of
the machine was used in the print data.
[Remedy] Check the print data.
116-741
[Cause] The form cannot be registered because the number of the form registration exceeds the
maximum number allowed.
[Remedy] Delete unnecessary form. The maximum number allowed is 2048.
116-742
[Cause] The logo data cannot be registered because the number of the logo data registration
exceeds the maximum number allowed.
[Remedy] Delete unnecessary logo data.
116-743
[Cause] The logo data or form cannot be registered because the memory for the form and logo
data is insufficient.
[Remedy] Increase memory.
116-746
[Cause] The form specified is not registered.
[Remedy] Use the form registered, or register the form.
116-747
[Cause] The paper margin value is too large for the HP-GL/2 (optional) active coordinates area.
[Remedy] Decrease the paper margin value, and then execute the operation again.
116-748
[Cause] There is no plot data in the HP-GL/2 (optional) print data.
[Remedy] Check the print data.
Error Code Cause and Remedy

Table of Contents

Other manuals for Fuji Xerox ApeosPort-IV C3375

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Fuji Xerox ApeosPort-IV C3375 and is the answer not in the manual?

Fuji Xerox ApeosPort-IV C3375 Specifications

General IconGeneral
Print Resolution1200 x 2400 dpi
FunctionsPrint, Copy, Scan, Fax
Duplex PrintingYes
Memory (Standard)2 GB
Copy Resolution600 x 600 dpi
Scan Resolution600 x 600 dpi
Fax Transmission Speed33.6 kbps
Operating System CompatibilityWindows, Mac OS, Linux
Print Speed35 ppm
ConnectivityEthernet, USB
Paper SizeA3, A4, A5, B4, B5
Hard Drive160 GB
Network ConnectivityEthernet
Copy Speed (Color)35 cpm
Copy Speed (Mono)35 cpm

Related product manuals