Furuno FSV25 User Manual

www.furuno.com
A
ll brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Installation Manual
COLOR SCANNING SONAR
Model FSV-25/FSV-25S
SAFETY INSTRUCTIONS ........................i
SYSTEM CONFIGURATION ..................iii
EQUIPMENT LISTS................................iv
1. HOW TO INSTALL THE SYSTEM ..1-1
1.1 Hull Unit (FSV-253/FSV-254)..............1-1
1.2 Processor Unit (FSV-2503/FSV-2503S)
............................................................1-7
1.3 Control Unit (FSV-2501) .....................1-9
1.4 Transceiver Unit (FSV-251) ..............1-12
1.5 Power Supply Unit (FSV-252)...........1-14
1.6 IF (Interface) Unit (FSV-8502) ..........1-15
1.7 Junction Box (FSV-2550)..................1-15
1.8 Raise/Lower Control Box (FSV-2530)
..........................................................1-15
1.9 Control Box Extension Box (FSV-2560)
..........................................................1-16
1.10 Attachment Flange (Option)..............1-17
1.11 Remote Controller (FSV-2504) .........1-18
2. WIRING............................................2-1
2.1 How to Connect the Units ...................2-1
2.2 Processor Unit ....................................2-2
2.3 IF Unit .................................................2-5
2.4 Control Unit and Remote Controller....2-7
2.5 Transceiver Unit..................................2-9
2.6 Junction Box .....................................2-11
2.7 Raise/Lower Control Box ..................2-12
2.8 Power Supply Unit ............................2-13
2.9 Control Box Extension Box ...............2-15
3. POST INSTALLATION SETTINGS .3-1
3.1 How to Set the Language ...................3-1
3.2 How to Set Up the Transducer............3-3
3.3 Hull Unit Checks .................................3-4
3.4 How to Access the System Menu .......3-8
3.5 How to Adjust the Heading .................3-9
3.6 How to Configure the Own Ship Mark
..........................................................3-10
3.7 How to Set Up a Secondary Monitor.3-10
3.8 Other System Menu Items ................3-11
APPENDIX 1 JIS CABLE GUIDE.....AP-1
APPENDIX 2
FRP TANK INSTALLATION .............AP-2
PACKING LISTS ................................. A-1
OUTLINE DRAWINGS ........................ D-1
INTERCONNECTION DIAGRAM........ S-1

Furuno FSV25 Specifications

General

Brand	Furuno
Model	FSV25
Category	Sonar
Language	English

Summary

SAFETY INSTRUCTIONS

DANGER

Indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Additional Warnings and Precautions

Further safety warnings and precautions for operation and installation.

1. HOW TO INSTALL THE SYSTEM

1.1 Hull Unit (FSV-253/FSV-254)

Installation of the hull unit, including handling notes.

1.2 Processor Unit (FSV-2503/FSV-2503S)

Installation of the processor unit, including mounting considerations.

1.3 Control Unit (FSV-2501)

Installation of the control unit, including console or desktop mounting.

1.4 Transceiver Unit (FSV-251)

Mounting the transceiver unit and reinforcing it against vibration.

1.5 Power Supply Unit (FSV-252)

Mounting options for the power supply unit.

1.6 IF (Interface) Unit (FSV-8502)

Mounting the IF unit on a bulkhead.

1.7 Junction Box (FSV-2550)

Installation of the junction box.

1.8 Raise/Lower Control Box (FSV-2530)

Installing the raise/lower control box and motion sensor.

1.9 Control Box Extension Box (FSV-2560)

Installation procedure for the optional control box extension.

1.10 Attachment Flange (Option)

Using an attachment flange for specific hull units.

1.11 Remote Controller (FSV-2504)

Installing the optional remote controller.

2. WIRING

2.1 How to Connect the Units

Overview of FSV-25 interconnections and equipment grounding.

2.2 Processor Unit

Connecting external units to the processor unit.

2.3 IF Unit

Connecting the IF unit and fabricating cables.

2.4 Control Unit and Remote Controller

Ground connection and remote controller connection.

2.5 Transceiver Unit

Connecting the IF unit and transducer cables.

2.6 Junction Box

Connecting the transceiver, hull unit, and signal cables via the junction box.

2.7 Raise/Lower Control Box

Connecting power and transceiver unit cables to the control box.

2.8 Power Supply Unit

Connecting the power supply and setting breaker configurations.

2.9 Control Box Extension Box

Installing the extension box and connecting fans.

3. POST INSTALLATION SETTINGS

3.1 How to Set the Language

Procedure to change the default display language of the equipment menus.

3.2 How to Set Up the Transducer

Entering limit switch location to display transducer protrusion.

3.3 Hull Unit Checks

Performing checks on the hull unit, including transmit status and operation.

3.4 How to Access the System Menu

Steps to access the system menu for advanced settings.

3.5 How to Adjust the Heading

Adjusting the heading alignment for the hull unit and motion sensor.

3.6 How to Configure the Own Ship Mark

Setting ship dimensions and transducer position for display.

3.7 How to Set Up a Secondary Monitor

Configuring display settings for a secondary monitor.

3.8 Other System Menu Items

Explanation of various menu items not previously described.

APPENDIX 2 FRP TANK INSTALLATION

Waterproofing gasket dimensions

Dimensions for the waterproofing gasket.

Prepare the following items

List of items required for FRP tank installation.

Installation

Step-by-step procedure for installing the unit in an FRP tank.