FUTABA 32MZ-WC User Manual

44
＜
Model Basic Setting Procedure
＞
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
1. Model addition and call
Default settings assign one model to the T32MZ-WC
transmitter. To add new models or select previously setup
models, use the Model Select function in the Linkage Menu.
When a new model is added, relink with the receiver used in
that model.
This is convenient when calling a model after registering the
model names in advance.
The currently selected model is displayed at the top of the
VFUHHQ%HIRUHÀ\LQJDQGEHIRUHFKDQJLQJDQ\VHWWLQJVDOZD\V
FRQ¿UPWKHPRGHOQDPH
Please be aware that the transmitter will stop transmitting
when you change the model.
When a new model is added, the model type select screen/
system mode/receiver link automatically appears. Please be
aware that the transmitter will stop transmitting when you
change the model..
2. Model type and swash type selection
When a separate model type is already selected, select
helicopter with the Model Type function of the Linkage Menu,
and then select the swash type matched to the helicopter.
+HOLFRSWHUEDVLFVHWWLQJSURFHGXUH
3. Flight condition addition
7KHWUDQVPLWWHUFDQLQVWDOOXSWRHLJKWÀLJKWFRQGLWLRQVSHU
model. You can assign all switches including sticks, switches,
trim levers and trim switches as flight-condition selection
switches. You can also add delayed mixing to these functions
in order to avoid sudden changes. Moreover, you can set
SULRULW\RUGHUIRUÀLJKWFRQGLWLRQVZKHQ\RXVHWPRUHWKDQRQH
condition. In addition, you can copy conditions and/or change
QDPHVRIFRQGLWLRQV7KLVFRPPDQGPD\DOVREHXVHGWRGH¿QH
what switches and/or controls are used to activate each flight
condition.
The Condition Select function automatically allocates the
default Condition 0 (Normal) for each model type. Condition
0 (Normal) is the only one active when a new model type is
defined. This condition is always ON, and remains ON until
other conditions are activated by switches.
The Condition Delay can be programmed for each channel.
The Condition Delay is used to change the servo throw smoothly
when switching conditions.
*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOH
ŏ1RUPDO8VHLQLWLDOVHWWLQJFRQGLWLRQVRSHUDWHZKHQ
switch OFF)
8VHIURPHQJLQHVWDUWLQJWRKRYHULQJ
ŏ,GOHXS6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW6:(
center)
8VHLQVWDOOWXUQORRSDQGRWKHUPDQHXYHUV
ŏ,GOHXS6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW6:(
forward side)
8VHLQUROOV
ŏ7KURWWOHKROG6ZLWFKVHWWLQJH[DPSOH2SHUDWHDW
SW-G forward side)
8VHLQDXWRURWDWLRQ
The priority is throttle hold/idle up 2/idle up 1/normal.
Throttle hold has the highest priority.
Add other conditions, as required.
+(/,&237(5

FUTABA 32MZ-WC Specifications

General

Brand	FUTABA
Model	32MZ-WC
Category	Remote Control
Language	English