FUTABA 32MZ-WC - System Type; Receiver linking; Dual receiver function (only FASSTest 26;18 CH mode)

83
＜
Linkage Menu
＞
+(/,&237(5
$,53/$1(*/,'(5
ڀ ŪŲŃƗƒŃŷŤťůŨŃŲũŃŦŲűŷŨűŷŶ
ڀ
Ū
Ū
Ų
Ų
Ɨ
Ɨ
ƒ
ŷ
ŷ
Ť
Ť
ť
ť
ů
ů
Ũ
Ũ
Ų
Ų
ũ
ũ
Ŧ
Ŧ
6\VWHP7\SHVHOHFWLRQ
7KH70=:&LVIRU*+]RQO\7KHV\VWHPFDQ
be changed from among 7 choices: FASSTest 26CH,
FASSTest 18CH, FASSTest 12CH, FASST MULTI,
FASST 7CH, S-FHSS, T-FHSS. Select the system
matched to the type of receiver you are using.u
*Even if it changes a system type, other model data is not
reset.
e
*If a system type is changed in the case of a helicopter, It
can choose out of two channel orders.
[Yes] : Selection sets the channel order suitable for system
type. (We recommend here.)
[No] : The present channel order is maintained.
*All control surfaces should be checked for the correct
operating directions and operating smoothness before
À\LQJWKHPRGHO
*Analog servos cannot be used with the FASSTest 12CH
mode.
5HFHLYHUOLQNLQJ
The receiver will only be controlled (without being
affected by other transmitters) by the transmitter it
is linked to. When using a receiver other than one
purchased as a set, linking is necessary.
Moreover, a re-link is required when a new model is
added by model selection, and the time of system type
change.
'XDOUHFHLYHUIXQFWLRQRQO\)$667HVW&+
PRGH
Dual receivers can be linked with the T32MZ-WC. Two
receivers are recognized individually by ID numbers.
)RUH[DPSOHLQ56%&+RXWSXWVHWWLQJIXQFWLRQLV
XVHGE\VHWWLQJWKH¿UVWDVDV&+DQGVHWWLQJWKH
VHFRQGDV&+WZRVHWVRIUHFHLYHUVFDQEHXVHGDV
a set in the model, allowing you 16 channels. If a dual
receiver function is used, the following function can set
up individually.
・
Battery fail-safe voltage setup
ŏ5HWXUQWR/LQNDJH0HQX
ŏ7RXFKWKH>6\VWHP7\SH@EXWWRQLQWKH/LQNDJH0HQX
WRFDOOWKHVHWXSVFUHHQVKRZQEHORZ
6\VWHP7\SH
6\VWHPPRGHVHWWLQJ5HFHLYHUOLQN
A telemetry function cannot be used for the 2nd receiver.
7KHYROWDJHDQG([WYROWDJHRIDQGUHFHLYHUFDQQRWEH
known with a transmitter.
7ULSOHUHFHLYHUIXQFWLRQRQO\)$667HVW&+
PRGH
Triple receivers can be linked with the T32MZ-WC.
Three receivers are recognized individually by ID
numbers.
$WHOHPHWU\IXQFWLRQFDQQRWEHXVHGIRUWKHQGUG
receiver. 7KHYROWDJHDQG([WYROWDJHRIDQGUG
receiver cannot be known with a transmitter.
・
Battery fail-safe voltage setup
$WHOHPHWU\IXQFWLRQFDQQRWEHXVHGIRUWKHQGUG
receiver. 7KHYROWDJHDQG([WYROWDJHRIDQGUG
receiver cannot be known with a transmitter.
7HOHPHWU\IXQFWLRQRQO\)$667HVWPRGH
To use the telemetry function, set “Telemetry” to “ON”.
'/,QWHUYDORQO\)$667HVWPRGH
When a telemetry function is enabled, the receiving
interval (down-link interval) of sensor data can be
changed.
,ID'/LQWHUYDOLVLQFUHDVHGWKHUHVSRQVHRIWKHVHQVRU
data display becomes slower, but stick response will
improve.
%DWWHU\IDLOVDIHYROWDJHVHWXS)$667HVW
7)+66PRGH
The voltage which battery fail-safe activates, can be set
ZKHQ\RXOLQN97KHUHFHLYHUPHPRUL]HVWKH
setting as it was at link.
Suggested setting voltages are as follows.
FHOOV1L&GRU1L0+1RUPDO V) = 3.8 V
• 2 cells LiFe (Normal: 6.6 V a V
FHOOV/L3R1RUPDO V a V
It is a rough reference value.
Since it changes with servos carried in the condition and
the model of a battery, please set to your own model in a
battery consumption current.