FUTABA 3PKS - Function; Function Select Dial (DIAL)

Initially set functions
DL1 :Dual rate function
DL2 :ATL function
DL3 :(Not set)
DT1 :Steering trim
DT2 :Throttle trim
DT3 :(Not set)
Abbrevia-
tion used on
setup screen
Abbreviation
displayed on
opening screen
Function name, etc
D/R (D/R) Dual rate function
ATL (ATL) ATL function
EXP-S (EXPS) Steering EXP
EXP-F (EXPF) Throttle EXP (Forward side)
EXP-B (EXPB) Throttle EXP (Brake side)
EXP-3 (EXP3) 3rd Channel brake EXP
SP-TN (SPTn) Steering speed (Turn side)
SP-RN (SPRn) Steering speed (Return side)
AB.P (AB.P) A.B.S. function (Return amount)
ABS.D (ABSD) A.B.S. function (Delay)
CYCLE (CYCL) A.B.S. function (cycle speed)
ACC-F (ACCF) Throttle acceleration (Forward side)
ACC-B (ACCB) Throttle acceleration (Brake side)
ACC-3 (ACC3) 3rd Channel brake acceration (BRAKE fanction-ON)
THSP1 (THS1) Throttle speed (ALL/LOW)
THSP2 (THS2) Throttle speed (MID)
THSP3 (THS3) Throttle speed (HIGH)
ST-TR (TRMS) Steering trim
TH-TR (TRMT) Throttle trim
CH3 (3CH) Channel 3
SUBT1 (SBT1) Sub trim (CH1)
SUBT2 (SBT2) Sub trim (CH2)
SUBT3 (SBT3) Sub trim (CH3)
D/R2 (D/R2) 2nd dual rate function
IDLUP (IDLE) Idle up function
TLT13 (TL13) Tilt mixing (1>3)
TLT31 (TL31) Tilt mixing (3>1)
PM1-A (PM1A) Program mixing 1 (RGHT/BRAK/DOWN sides)
PM1-B (PM1B) Program mixing 1 (LEFT/FWRD/UP sides)
PM2-A (PM2A) Program mixing 2 (RGHT/BRAK/DOWN sides)
PM2-B (PM2B) Program mixing 2 (LEFT/FWRD/UP sides)
BK-RT (BKRT) Brake mixing (3ch brake rate)
BK-DL (BKDL) Brake mixing (delay)
B-ABP (BABP) 3rd Channel A.B.S -Return amount (BRAKE fanction-ON)
B-ABD (BABD) 3rd Channel A.B.S -Delay(BRAKE fanction-ON)
OFF Not used
Settable functions (DL1/DL2/DL3, DT1/DT2/DT3)
DL1 DL2
DL3 DT1
DT2
DT3
80
Function
Function Select Dial "DIAL"
Function Select Dial "DIAL"
This function allows selection of the function performed by the digital dial (DL1/DL2/
DL3) and digital trimmers (DT1/DT2/DT3), step amount adjustment, and operating di-
rection reversal.
- The table below lists the functions that can be assigned to each dial
and digital trimmer. The assigned function is also displayed on the
opening screen together with the current adjustment value. They are
displayed in DT1, DT2, DT3, DL1, DL2, and DL3 order, from top to bottom.
- The step amount can be adjusted. The table below shows the relationship between set value and step
amount.
- The operation direction can be reversed. (NOR/REV)