AN-4# Analog Input X30/12 SP-## Special Functions SP-5# Environment
O-13 Configurable Status Word
STW O-8# Drive Port Diagnostics
AN-40 Terminal X30/12 Low Voltage SP-1# Line On/Off SP-50 RFI Filter O-3# Drive Port Settings O-80 Bus Message Count
AN-41 Terminal X30/12 High Voltage SP-10 Line failure SP-51 DC Link Compensation O-30 Protocol O-81 Bus Error Count
AN-44 Term. X30/12 Low Ref./Feedb.
Value SP-11 Line Voltage at Input Fault SP-53 Fan Monitor O-31 Address O-82 Slave Messages Rcvd
AN-45 Term. X30/12 High Ref./Feedb.
Value SP-12 Function at Line Imbalance SP-55 Output Filter O-32 Drive Port Baud Rate O-83 Slave Error Count
AN-46 Term. X30/12 Filter Time
Constant SP-2# Reset Functions
SP-59 Actual Number of Inverter
Units O-33 Drive Port Parity O-89 Diagnostics Count
AN-47 Term. X30/12 Live Zero SP-23 Typecode Setting SP-6# Automatic Derate O-34 Estimated cycle time O-9# Bus Jog / Feedback
AN-5# Analog Output 42 SP-25 Trip Delay at Torque Limit
SP-60 Function at Over
Temperature O-35 Minimum Response Delay O-90 Bus Jog 1 Speed
AN-50 Terminal 42 Output SP-26 Trip Delay at Drive Fault
SP-61 Function at Drive
Overload O-36 Maximum Response Delay O-91 Bus Jog 2 Speed
AN-51 Terminal 42 Output Min Scale SP-28 Production Settings
SP-62 Drive Overload Derate
Current O-37 Maximum Inter-Char Delay O-94 Bus Feedback 1
AN-52 Terminal 42 Output Max Scale SP-29 Service Code O-## Options / Comms O-4# Drive MC protocol set O-95 Bus Feedback 2
AN-53 Terminal 42 Output Bus Control SP-3# Current Limit Ctrl. O-0#General Settings O-40 Telegram Selection O-96 Bus Feedback 3
AN-54 Terminal 42 Output Timeout
Preset SP-30 Current Lim Ctrl, Proportional Gain O-01 Control Site O-42 PCD write configuration AO-## Analog I/O Option
AN-6# Analog Output X30/8 SP-31 Current Lim Ctrl, Integration Time O-02 Control Word Source O-43 PCD read configuration AO-0# Analog I/O Mode
AN-60 Terminal X30/8 Output SP-32 Current Lim Ctrl, Filter Time
O-03 Control Word Timeout
Time O-5# Digital/Bus AO-00 Terminal X42/1 Mode
AN-61 Terminal X30/8 Min. Scale SP-4# Energy Savings
O-04 Control Word Timeout
Function O-50 Coasting Select AO-01 Terminal X42/3 Mode
AN-62 Terminal X30/8 Max. Scale SP-40 VT Level O-05 End-of-Timeout Function O-52 DC Brake Select AO-02 Terminal X42/5 Mode
AN-63 Terminal X30/8 Output Bus
Control SP-41 Energy Savings Min. Magnetization
O-06 Reset Control Word
Timeout O-53 Start Select AO-1# Analog Input X42/1
AN-64 Terminal X30/8 Output Timeout
Preset SP-42 Energy Savings Min. Frequency O-07 Diagnosis Trigger O-54 Reversing Select AO-10 Terminal X42/1 Low Voltage
SP-43 Motor Cosphi O-1# Control Settings O-55 Set-up Select AO-11 Terminal X42/1 High Voltage
O-10 Control Word Profile O-56 Preset Reference Select
AO-14 Term. X42/1 Low Ref./Feedb.
Value
Table 5.5
About Programming AF-600 FP Design and Installation Guide
5-8 DET-768A
5
To Next Page
Loading...
