GE M60 UR Series - Page 658

vi M60 Motor Protection System GE Multilin
INDEX
NEUTRAL DIRECTIONAL OVERCURRENT
FlexLogic operands...................................................... 5-122
logic ............................................................................ 5-190
polarization.................................................................. 5-188
settings ....................................................................... 5-186
specifications................................................................. 2-18
NEUTRAL INSTANTANEOUS OVERCURRENT
see entry for NEUTRAL IOC
NEUTRAL IOC
FlexLogic operands...................................................... 5-122
logic ............................................................................ 5-185
Modbus registers ...........................................................B-35
settings ....................................................................... 5-185
specifications................................................................. 2-17
NEUTRAL OVERVOLTAGE
FlexLogic operands...................................................... 5-122
logic ............................................................................ 5-211
Modbus registers ...........................................................B-44
settings ....................................................................... 5-211
specifications................................................................. 2-19
NEUTRAL TOC
specifications................................................................. 2-17
NON-VOLATILE LATCHES
FlexLogic operands...................................................... 5-121
Modbus registers ...........................................................B-53
settings ....................................................................... 5-138
specifications................................................................. 2-20
O
ONE SHOTS .................................................................. 5-128
OPERATING TEMPERATURE .......................................... 2-26
OPERATING TIMES ......................................................... 2-17
ORDER CODES ....................... 2-8, 2-10, 2-11, 2-13, 6-29, 7-3
ORDER CODES, UPDATING .............................................. 7-3
ORDERING..............................................2-8, 2-10, 2-11, 2-13
OSCILLATORY TRANSIENT TESTING ............................. 2-27
OSCILLOGRAPHY
actual values ................................................................. 6-28
clearing .................................................................. 5-25, 7-2
Modbus .......................................................................... B-6
Modbus registers ..................................................B-18, B-29
settings .........................................................................5-70
specifications................................................................. 2-21
via COMTRADE .............................................................. B-6
via EnerVista software .....................................................4-2
OUTPUTS
contact outputs ............................................................ 5-254
control power................................................................. 2-24
critical failure relay ........................................................ 2-24
Fast Form-C relay .......................................................... 2-24
Form-A relay .......................................2-23, 3-12, 3-13, 3-18
Form-C relay ................................................2-24, 3-12, 3-18
latching outputs .................................................. 2-23, 5-254
remote outputs ..................................................5-259, 5-260
virtual outputs.............................................................. 5-256
OVERCURRENT CURVE TYPES .................................... 5-191
OVERCURRENT CURVES
definite time................................................................. 5-195
FlexCurves .................................................................. 5-195
I2T .............................................................................. 5-195
IAC ............................................................................. 5-194
IEC ............................................................................. 5-193
IEEE ........................................................................... 5-191
OVERFREQUENCY
FlexLogic operands ......................................................5-122
logic ............................................................................5-226
settings........................................................................5-226
specifications .................................................................2-19
OVERFRQUENCY
Modbus registers........................................................... B-37
OVERVOLTAGE
auxiliary .............................................................. 2-19, 5-214
negative sequence .......................................................5-212
negative-sequence .........................................................2-19
neutral ................................................................ 2-19, 5-211
phase ................................................................. 2-19, 5-210
P
PANEL CUTOUT ........................................................ 3-1, 3-2
PARALLEL REDUNDANCY PROTOCOL
actual values..................................................................6-13
explained .......................................................................5-31
settings..........................................................................5-30
specifications .................................................................2-25
PARITY ............................................................................5-27
PASSWORD SECURITY
FlexLogic operands ......................................................5-126
PASSWORDS
bypass authentication.....................................................5-21
changing ........................................................................4-28
for settings templates ...................................................... 4-5
lost password .................................................................. 5-8
Modbus........................................................................... B-7
Modbus registers.................................................. B-17, B-26
overview ........................................................................1-19
security........................................................................... 2-3
settings........................................................................... 2-3
PC SOFTWARE
see entry for ENERVISTA UR SETUP
PERMISSIVE FUNCTIONS..............................................5-207
PER-UNIT QUANTITY........................................................ 5-4
PHASE ANGLE METERING ..............................................6-15
PHASE CURRENT METERING .........................................6-18
PHASE DIRECTIONAL OC
Modbus registers........................................................... B-40
PHASE DIRECTIONAL OVERCURRENT
FlexLogic operands ......................................................5-122
logic ............................................................................5-184
phase A polarization.....................................................5-182
settings............................................................. 5-182, 5-183
specifications .................................................................2-18
PHASE INSTANTANEOUS OVERCURRENT
see entry for PHASE IOC
PHASE IOC
FlexLogic operands ......................................................5-122
logic ............................................................................5-181
specifications .................................................................2-17
PHASE OVERVOLTAGE
FlexLogic operands ......................................................5-123
logic ............................................................................5-210
Modbus registers........................................................... B-40
settings........................................................................5-210
specifications .................................................................2-19
PHASE ROTATION ...........................................................5-99
PHASE TIME OVERCURRENT
see entry for PHASE TOC
PHASE TOC
specifications .................................................................2-17