TRX-VI-33100 Module
Planning and Installation Manual 201
Figure 117. Video processing menu for NTSC, showing setup for all 16 inputs. PAL display is
similar. (Only Input 0 is connected in this example.)
Video Processor -
--------------------------------------------------------------------------------
Reference - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
================================================================================
Disable (Off) 0
Enable (On) 1
Contrast/Y Gain: Brightness/Y Offset:
50.0% to 200.0% (0.5% steps) -100.1 to +100.1Deg (0.7mV steps)
Saturation/Chroma Gain: Hue/Chroma Phase:
50.0% to 200.0% (0.5% steps) -180.0 to +180.0Deg (1.0Deg steps)
--------------------------------------------------------------------------------
+------------------------------------------- Channel Line Rate --------+
| |
| +----------------------------------- Insert EDH (On/Off) |
| | +------------------------------- Contrast / Y Gain (%) |
| | | +---------------------- Saturation / Chroma Gain (%) |
| | | | +-------------- Brightness / Y Offset (mV) |
| | | | | +------ Hue / Chroma Phase (Deg) |
+---+---+--------+-------+-------+-------------------------------------------+--
0, 0, 100.0, 100.0, +000.0, +000.0 525
1, 0, 100.0, 100.0, +000.0, +000.0 N/A
2, 0, 100.0, 100.0, +000.0, +000.0 N/A
3, 0, 100.0, 100.0, +000.0, +000.0 N/A
4, 0, 100.0, 100.0, +000.0, +000.0 N/A
5, 0, 100.0, 100.0, +000.0, +000.0 N/A
6, 0, 100.0, 100.0, +000.0, +000.0 N/A
7, 0, 100.0, 100.0, +000.0, +000.0 N/A
8, 0, 100.0, 100.0, +000.0, +000.0 N/A
9, 0, 100.0, 100.0, +000.0, +000.0 N/A
a, 0, 100.0, 100.0, +000.0, +000.0 N/A
b, 0, 100.0, 100.0, +000.0, +000.0 N/A
c, 0, 100.0, 100.0, +000.0, +000.0 N/A
d, 0, 100.0, 100.0, +000.0, +000.0 N/A
e, 0, 100.0, 100.0, +000.0, +000.0 N/A
f, 0, 100.0, 100.0, +000.0, +000.0 N/A
Press: '0 ~ 9' or 'A ~ F' to select channel to edit.
Press: 'M' to move/copy channel configuration.
Press: 'Z' to set ALL channels to factory defaults.
Press 'ESC' to return to Main Menu.
When an input (channel) is selected, the display will show the values for
that particular channel:
Figure 118. Video processing setup menu for one channel (NTSC shown).
Video Processor -
--------------------------------------------------------------------------------
Reference - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
================================================================================
Selected - Input 0: Line Rate: 525 Line Type: NTSC (M, J)
--------------------------------------------------------------------------------
Disable (Off) 0
Enable (On) 1
Contrast/Y Gain: Brightness/Y Offset:
50.0% to 200.0% (0.5% steps) -100.1 to +100.1Deg (0.7mV steps)
Saturation/Chroma Gain: Hue/Chroma Phase:
50.0% to 200.0% (0.5% steps) -180.0 to +180.0Deg (1.0Deg steps)
--------------------------------------------------------------------------------
+------------------------------------------- Channel Line Rate --------+
| |
| +----------------------------------- Insert EDH (On/Off) |
| | +------------------------------- Contrast / Y Gain (%) |
| | | +---------------------- Saturation / Chroma Gain (%) |
| | | | +-------------- Brightness / Y Offset (mV) |
| | | | | +------ Hue / Chroma Phase (Deg) |
+---+---+--------+-------+-------+-------------------------------------------+--
0, 0, 100.0, 100.0, +000.0, +000.0 525
To Disable/Enable Insert EDH press: 'W'.
To Decrement/Increment Contrast/Y Gain press: 'F'/'G'.
To Decrement/Increment Saturation/Chroma Gain press: 'V'/'B'.
To Decrement/Increment Brightness/Y Offset press: 'H'/'J'.
To Decrement/Increment Hue/Chroma Phase press: 'N'/'M'.
Press: 'ESC' to ABORT changes and return to the previous Menu.
Press: 'Enter' to ACCEPT changes and select a different channel.
Press: 'Y' to revert back to last settings.
Press: 'Z' to set THIS channel to factory defaults.
To Next Page
Loading...
Need help?
General
