Why won't my Hisun Offroad Vehicle engine start?
If your Hisun Offroad Vehicle's engine won't start, first ensure the key and emergency shut-off switch are in the “ON” position. Then, check the fuel level and make sure the spark plug is secure with the cap attached. If issues persist, a service center can inspect the electrical circuits.
How to improve brake performance on my Hisun AXIS 110 Offroad Vehicle?
If you notice a degradation in your Hisun Offroad Vehicle's braking performance, start by checking if the brake disc wear limit has been exceeded and replace the disc if necessary. Also, check whether the rotors or the disc brake pads have worn beyond limits or are contaminated; change parts if needed. Inspect brake lines for leaks and replace them if necessary. Furthermore, inspect the push rod to the master cylinder and replace the master cylinder if deformed. Check if brake lines have any air; if they do, use special brake bleeding tools to remove air. Finally, check to see if there is sufficient brake fluid in the brake reservoir, ensuring it's above the minimum mark.
How to fix lights not working on Hisun AXIS 110?
If the lights on your Hisun Offroad Vehicle are not working, first check to ensure the light switch is functioning correctly and replace it if needed. Next, inspect the wires for any damage and replace them if necessary. Finally, check the lights themselves for damage or burnout, replacing them as needed.
Why is the steering loose on my Hisun AXIS 110 Offroad Vehicle?
If the steering on your Hisun Offroad Vehicle feels loose, start by checking the nuts on the steering column, steering knuckles, and steering stem and tighten them if necessary. Then, inspect the steering column for any damage. Finally, inspect the tie rods for looseness or damage, replacing them if needed.
What to do if front wheels shake on Hisun Offroad Vehicle?
If the front wheels of your Hisun Offroad Vehicle shake while driving, inspect the tie rods for looseness or damage and replace if needed. Check the lug nuts on the front wheels for looseness and tighten if needed. Inspect the bearings in the front wheel hub for damage or excessive wear, replacing the bearings if necessary. Also, check all rubber bushings for damage in the front end assembly, replacing them if needed.
Why does my Hisun AXIS 110 Offroad Vehicle engine backfire?
If your Hisun Offroad Vehicle engine backfires, check for air leaks in the air filter or air inlet pipe and replace if needed. Also, check the connection between the exhaust pipe and engine, or the exhaust pipe and muffler, for air leaks, repairing or replacing as needed. Finally, check the grade of gasoline; if it's too low, the engine may backfire.
Why do rear wheels shake while driving Hisun AXIS 110?
If the rear wheels shake while driving your Hisun Offroad Vehicle, check the bearings in the rear axle assembly for damage and replace if needed. Check the swing arm bearing for damage and replace if needed. Check the retainer nuts holding the rear wheels on for looseness or damage. Check the internal splines of the rear wheel hub and outer splines of the rear axle for excessive wear or damage, replacing the axle or wheel hub if needed. Check all rubber bushings for damage in the rear end assembly, replacing if needed.
Why do the brakes on my Hisun AXIS 110 make noise and overheat?
If the front or rear brakes of your Hisun Offroad Vehicle make noise or the brake discs or rotors turn red due to heat, check if the brake discs are deformed and replace if needed. Also, check the hydraulic cylinder on brake calipers for blockage, and the calipers for deformation, replacing if needed.
What to do if shutdown switch doesn't turn off engine on Hisun AXIS 110?
If the shutdown switch on your Hisun Offroad Vehicle does not turn off the engine, check to see if the shutdown switch itself has a problem and replace it if needed. Also, check the wires for damage and replace or repair them if necessary. Finally, check to see if the ECU or the EFI systems is damaged and have a service center repair it if needed.
Why is the brake system seizing on my Hisun Offroad Vehicle?
If the brake system on your Hisun Offroad Vehicle is seizing, check if the parking brake releases when returned to the off position. Check the brake discs on the front and rear wheels for deformation. Inspect the brake calipers on the front and rear wheels, the hydraulic cylinder on calipers for blockage, and the calipers for any deformation.
General| Brand | Hisun |
|---|---|
| Model | AXIS 110 |
| Category | Offroad Vehicle |
| Language | English |
Information for parents regarding ATV operation by children, age recommendations, and supervision.
Recommends ATV training courses for new operators.
Emphasizes the importance of reading and understanding the manual for safe operation.
Illustrates the placement of warning and specification labels on the utility model ATV.
Illustrates label placements for the sport model ATV.
Warns that ATVs are not toys and can be hazardous if not operated properly.
Specifies age limits and supervision requirements for ATV operation.
Lists essential safety practices like not consuming alcohol, speed limits, and proper control.
Guides on safe operation on hills, inclines, and different terrains.
Details precautions for handling gasoline, refueling, and potential hazards.
Identifies key controls like meter, gear shift, ignition, and brakes on the ATV.
Explains how to locate and record the Vehicle Identification Number (VIN).
Explains the function of gear indicators, park indicator, and coolant warning light.
Details the components of the multi-function meter and how to set odometers and clock.
Explains master key switch operation and identifies left hand controls.
Explains throttle control operation and how to use foot and hand brake levers.
Details shock adjustment and chain slack/adjustment procedures.
Lists essential items to check before operating the ATV, including brakes, fuel, and tires.
Details how to inspect the brake system fluid, hoses, and perform a braking test.
Recommends fuel type and warns about refueling; covers tire pressure and wear.
Step-by-step guide to starting the ATV engine, including safety checks.
Detailed instructions on how to safely jump-start the ATV using another battery.
Details how to shift gears and operate in reverse with necessary precautions.
Guides on how to break in the new engine during the first 20 hours of operation.
Details essential safety gear including helmets, eye protection, and protective clothing.
Emphasizes practice, familiarization, and proper turning techniques for safe riding.
Guides on safe hill climbing, descending, and operating on slopes.
Highlights the importance of following maintenance procedures for safety and lifespan.
Details how to check/change engine oil and filter, and recommended oil types.
Covers brake pad inspection, fluid replacement, and related maintenance.
Explains fuse inspection/replacement and headlight/taillight bulb replacement.
Provides troubleshooting tips for the fuel system, emphasizing fire safety.
Troubleshooting steps for brake system seizing and performance degradation.
Addresses engine starting issues, idle problems, backfires, and low-temperature starting.
Details the steps for cleaning the ATV, including precautions for pressure washers.
Steps for preparing the ATV for storage, including fuel stabilizer and engine protection.
Lists ATV dimensions, engine type, displacement, and bore x stroke.
Details specifications for oils, filters, fuel, spark plugs, and clutch type.
Outlines specifications for the brake, suspension, and tire systems.
Lists diagnostic trouble codes (DTCs) related to MAP, IAT, and coolant/oil sensors.
Lists DTCs for O2 sensors, injectors, FPR coil, CKP sensor, and ignition coils.
Lists DTCs for system voltage, MIL circuit, tachometer, O2 sensors, VSS, and CCP.
Explains warranty coverage, owner responsibilities, and contact information.
Lists conditions not covered by the warranty and liability limits.
To Next Page
