To Next PageTo Next Page
Need help?Do you have a question about the Hitachi RAS-(4-6)HVRNS2E and is the answer not in the manual?
General| Cooling Capacity (kW) | 4.0-6.0 |
|---|---|
| SEER | 6.1 |
| SCOP | 4.0 |
| Energy Efficiency Cooling | A++ |
| Energy Efficiency Heating | A+ |
| Refrigerant | R32 |
| Power Supply | 220-240V, 50Hz |
| Coefficient of Performance (COP) | 3.8 |
| Outdoor Unit Dimensions (W x H x D) | 800 x 550 x 285 mm |
| Indoor Unit Weight | 11 kg |
| Outdoor Unit Weight | 35 kg |
| Type | Split system |
| Noise Level (Outdoor Unit) | 50 ~ 55 dB(A) |
| Energy Efficiency Ratio (EER) | 3.2 ~ 3.5 |
General notes, introduction to series, and environment-friendly aspects.
Explanation of symbols used for safety and general information in the manual.
Classification and product guide for IVX and ES series outdoor unit models.
Summary of safety precautions for unit installation, including danger and caution points.
Guidelines for safely transporting the outdoor unit, including hanging methods.
Information on the center of gravity for hanging and moving the outdoor unit.
Details of factory-supplied accessories for specific RAS models.
Requirements for installation space around outdoor units for various models and configurations.
Requirements for installation location and foundation, including drainage considerations.
Installation procedures for optional accessories like air flow guides, wind guards, and snow protection hoods.
General notes on drain piping, connections, and insulation requirements.
Considerations for piping materials, connection methods, brazing, and insulation.
Piping connection details for IVX series outdoor units, including different connection directions.
Piping connection details for ES series outdoor units.
General checks before installing electrical wiring, including safety precautions.
Electrical wiring connections and DIP switch settings for IVX series outdoor units.
Electrical wiring connections and DIP switch settings for ES series outdoor units.
Guidelines for connecting electrical wires between indoor and outdoor units, including H-LINK system.
Recommended wire sizes for power and transmitting cables based on current and series.
Electrical wiring diagrams for IVX and ES series outdoor units.
Explanation of control systems for IVX and ES series, detailing component functions in different modes.
Identification and indication details for outdoor unit PCBs for IVX and ES series.
Details on protection and safety controls for IVX and ES series outdoor units.
Flowcharts illustrating standard operation sequences for cooling, heating, and defrosting in IVX and ES series.
Standard control functions for IVX and ES series, including freezing protection and high discharge gas temperature prevention.
Details on available ports and configuration for optional functions on IVX and ES series outdoor units.
Pre-test run checks, including wiring, refrigerant, settings, and safety.
Step-by-step guide for performing a test run using a wired remote control switch.
Procedure for conducting a test run using a wireless remote control switch.
Steps for performing a test run directly from the outdoor unit's DIP switches.
Checklists for verifying correct operation and parameters of IVX and ES series units during test runs.
Initial troubleshooting steps for IVX and ES series, focusing on 7-segment display indications and power supply issues.
Procedures for troubleshooting IVX and ES series, covering alarm codes, check modes, and specific fault causes.
Procedures for checking main components like PCBs, remote controls, and specific parts using self-checking methods.
List and diagrams of spare parts for IVX series outdoor units.
List and diagrams of spare parts for ES series outdoor units.
Introduction to servicing operations, including safety precautions and general notes.
Detailed servicing procedures for IVX series outdoor units, including component removal steps.
Servicing procedures for ES series outdoor units, covering component removal steps.
Specifications and protective functions for inverters in IVX and ES series.
Information on thermistors for outdoor units, including their locations and resistance characteristics.
Details on the operation, specifications, and wiring of electronic expansion valves.
Explanation of the high-pressure protection device and its gas by-pass circuit.
Specifications and circuit diagrams for noise filters used in 3-phase and 1-phase power supplies.
Specifications for capacitors used in the inverter circuit.
Specifications for reactors used in 3-phase and 1-phase inverter circuits.
Information on the reliable mechanism and principle of compression for scroll compressors.
Procedure for checking power source and wiring connections for abnormal operations.
Analysis of burnt-out compressors due to insufficient refrigerant charge, including a field example.
Diagnosis and countermeasures for insufficient cooling performance related to long piping installations.
Troubleshooting high operation sound in ceiling-type indoor units, often related to installation or airflow.
Explanation and countermeasure for Alarm code "31", related to indoor unit capacity settings.
Troubleshooting poor cooling performance caused by insufficient installation space for outdoor units.
Precautions regarding refrigerant leakage, permissible concentrations, calculation, and countermeasures.
General maintenance procedures for indoor and outdoor units, covering fans, heat exchangers, piping, and electrical components.
Forms for recording service and maintenance activities.
