Hitachi SJ700-4000HFU2 - Page 226

Chapter 4 Explanation of Functions
4-155
Register
No.
Function name
Function code
R/W
Monitoring and setting items Data resolution
Data
resolution
142Ah
Frequency arrival setting for accel.
C042 (high)
R/W
0 to 40000
0.01 [Hz]
142Bh
C042 (low)
R/W
142Ch
Frequency arrival setting for decel.
C043 (high)
R/W
0 to 40000
0.01 [Hz]
142Dh
C043 (low)
R/W
142Eh
PID deviation level setting
C044
R/W
0 to 1000
0.1 [%]
142Fh
Frequency arrival setting for
acceleration (2)
C045 (high)
R/W
0 to 40000
0.01 [Hz]
1430h
C045 (low)
R/W
1431h
Frequency arrival setting for
deceleration (2)
C046 (high)
R/W
0 to 40000
0.01 [Hz]
1432h
C046 (low)
R/W
1433h to
1437h
(Reserved)
-
-
Inaccessible
-
1438h
Maximum PID feedback data
C052
R/W
0 to 1000
0.1 [%]
1439h
Minimum PID feedback data
C053
R/W
0 to 1000
0.1 [%]
143Ah
(Reserved)
R/W
-
143Bh
Over-torque (forward-driving) level
setting
C055
R/W
0 to 200
1 [%]
143Ch
Over-torque (reverse regenerating)
level setting
C056
R/W
0 to 200
1 [%]
143Dh
Over-torque (reverse driving) level
setting
C057
R/W
0 to 200
1 [%]
143Eh
Over-torque (forward regenerating)
level setting
C058
R/W
0 to 200
1 [%]
143Fh
(Reserved)
-
-
Inaccessible
-
1440h
(Reserved)
-
-
Inaccessible
-
1441h
Electronic thermal warning level
setting
C061
R/W
0 to 100
1 [%]
1442h
Alarm code output
C062
R/W
0 (disabling alarm output), 1 (3 bits), 2 (4 bits)
-
1443h
Zero speed detection level
C063
R/W
0 to 10000
0.01 [Hz]
1444h
Heat sink overheat warning level
C064
R/W
0 to 200
1 [℃]
1445h to
144Ah
(Reserved)
-
-
Inaccessible
-
144Bh
Communication speed selection
C071
R/W
2 (loopback test), 3 (2,400 bps), 4 (4,800 bps), 5
(9,600 bps), 6 (19,200 bps)
-
144Ch
Node allocation
C072
R/W
1. to 32.
-
144Dh
Communication data length selection
C073
R/W
7 (7 bits), 8 (8 bits)
-
144Eh
Communication parity selection
C074
R/W
00 (no parity), 01 (even parity), 02 (odd parity)
-
144Fh
Communication stop bit selection
C075
R/W
1 (1 bit), 2 (2 bits)
-
1450h
Selection of the operation after
communication error
C076
R/W
0 (tripping), 1 (tripping after decelerating and
stopping the motor), 2 (ignoring errors), 3 (stopping
the motor after free-running), 4 (decelerating and
stopping the motor)
-
1451h
Communication timeout limit
C077
R/W
0 to 9999
0.01 [sec.]
1452h
Communication wait time
C078
R/W
0 to 1000
1 [msec.]
1453h
Communication mode selection
C079
R/W
0 (ASCII), 1 (Modbus-RTU)
-
1454h
(Reserved)
-
-
Inaccessible
-
1455h
[O] input span calibration
C081
R/W
0 to 65530
1
1456h
[OI] input span calibration
C082
R/W
0 to 65530
1
1457h
[O2] input span calibration
C083
R/W
0 to 65530
1
1458h
(Reserved)
-
-
Inaccessible
-
1459h
Thermistor input tuning
C085
R/W
0 to 10000
0.1
145Ah to
145Eh
(Reserved)
-
-
Inaccessible
-
145Fh
Debug mode enable
C091
R
0/1
-
1460h to
1468h
(Reserved)
-
-
Inaccessible
-
1469h
Up/Down memory mode selection
C101
R/W
0 (not storing the frequency data), 1 (storing the
frequency data)
-
146Ah
Reset mode selection
C102
R/W
0 (resetting the trip when RS is on), 1 (resetting the
trip when RS is off), 2 (enabling resetting only upon
tripping [resetting when RS is on]), 3(resetting only
trip)
-
146Bh
Restart mode after reset
C103
R/W
0 (starting with 0 Hz), 1 (starting with matching
frequency), 2 (restarting with active matching
frequency)
-
146Ch
(Reserved)
-
-
Inaccessible
-
146Dh
FM gain adjustment
C105
R/W
50 to 200
1 [%]
146Eh
AM gain adjustment
C106
R/W
50 to 200
1 [%]
146Fh
AMI gain adjustment
C107
R/W
50 to 200
1 [%]
Register No.
Function name
Function code
R/W
Monitoring and setting items Data resolution
Data