Honeywell INTELLIGUARD 9000 - Area Keypad; Quick User Guide

INTELLIGUARD 9000™
9 74-3047—1
3.
Carefull
y
remove the circuit board. Do not touch an
y
of
the circuits or chips.
4.
Mount the BIC-6 on the wall usin
g
four No. 6 round or
pan head screws.
NOTE: Feed the re
q
uired cables into the BIC-6 base b
y
usin
g
the two s
q
uare holes in the base wirin
g
chan-
nel or remove the knockouts on either end of the wir-
in
g
channel to pass the cables throu
g
h the openin
g
s.
5.
Carefull
y
replace the circuit board.
6.
Connect all the wires to the BIC-6 as shown in Fi
g
. 9.
7.
Repeat steps 1 throu
g
h 6 for each BIC-6.
8.
When installation is complete and power is applied,
learn the BIC-6s.
NOTE: Steps 8a. throu
g
h 8h. ma
y
be replaced b
y
usin
g
the
PRO 9000 software. See the Commission section,
steps 1a. throu
g
h 1c., for more information.
a. Make sure the LED DS1 on each installed BIC-6
displa
y
s
C
.
b. On each BIC-6, press the
S2
(
ACCEPT
)
button to
place them in the COMMUNICATION STATUS dis-
pla
y
mode.
c. The center se
g
ment
(
RECEIVE
)
of the seven se
g
-
ment LED displa
y
(
BIC-6 DS1
)
flashes to indicate
incomin
g
data.
d. The decimal point on the LED displa
y
(
BIC-6, DS1
)
of each BIC-6 is off.
e. From the CC2, select CONFIGURATION from the
MODE Menu.
f. From the CC2, select LEARNING MODE.
g
. From the CC2, select DEVICES WITH SERIAL #.
The CC2 displa
y
s
Searching
. The decimal point
li
g
hts on the LED displa
y
(
BIC-6, DS1
)
on each BIC-
6 indicatin
g
the
y
are in the LEARNING MODE.
h. From each BIC-6, press and hold the
S2
(
ACCEPT
)
button for approximatel
y
two seconds, or until the
bottom se
g
ment
(
TRANSMIT
)
of the LED displa
y
DS1 flashes and the decimal point turns off. When
the decimal point disappears, the device is learned.
NOTE: If the BIC-6 had previousl
y
been learned, the deci-
mal point would have turned on and then turned off
almost immediatel
y
.
i. When the
ACCEPT
ke
y
is pressed on the CC2, the
I9000 exits the LEARNING MODE and displa
y
s the
total number of devices known b
y
the s
y
stem,
includin
g
the BIC-6s.
j
. From the CC2, exit the CONFIGURATION menu for
chan
g
es to become effective.
k. The bottom se
g
ment
(
TRANSMIT
)
of the LED dis-
pla
y
(
BIC-6, DS1
)
flashes ever
y
time the BIC-6 is
polled
(
addressed
)
. The center se
g
ment
(
RECEIVE
)
also flashes.
9.
Confi
g
ure each loop in the BIC-6, as needed, for the
specific inputs and outputs. See Loop Parameters and
Pro
g
rammin
g
section.
10.
Test the input loops locall
y
usin
g
the
ALARM
status
mode of the BIC-6 displa
y
. Refer to the Communication
and Alarm Displa
y
section. The inputs must still be
tested from the I9000 usin
g
the CC2 when the I9000
pro
g
rammin
g
is completed.
(
The outputs ma
y
onl
y
be
tested from the I9000 usin
g
the CC2 when the I9000
pro
g
rammin
g
is completed.
)
11.
Replace the BIC-6 cover.
12.
Repeat steps 9 throu
g
h 11 for each BIC-6.
Fig. 9. BIC-6 internal view.
NOTE: TB1 COM and VDD connect to 12 Vdc whereas TXRX- and TXRX+ connect to the CU COM 1 or 2, but not both. TB2
and TB3 connect to input points
(
see Fi
g
. 10, Loop T
y
pe 0, 2 or 4 for input wirin
g
confi
g
urations
)
, or output points
(
see
Fi
g
. 10, Loop T
y
pe 3 for output wirin
g
confi
g
urations
)
.
1
2
3
4
5
6
1
2
3
4
1
2
3
4
5
6
TB1
TB2
TB3
S3
S2
S1
DS1
RECEIVE
DISPLAY IN
COMMUNICATION
STATUS MODE
QUIT
QUITTER
ACCEPT
ACCEPTER
NEXT
SUIVANT
A1 COP
NO. 8003-243
COM
VDD
TXRX-
TXRX+
LP1-
LP1+
LP2-
LP2+
LP3-
LP3+
LP4-
LP4+
LP5-
LP5+
LP6-
LP6+
BIC-6 CONCENTRATOR UNIT
8003-238
M16066B
MOUNTING HOLES (4)
CU COM
12 VDC
INPUT
SUCH AS
MOTION
SENSOR
OUTPUT
SUCH AS
BUZZER
INPUT
OUTPUT
+
–
+
–
TRANSMIT
LEARN
1
1
REFER TO POSSIBLE LOOPS, CIRCUITS
FOR BIC-6 DEVICE DIAGRAM, LOOP TYPE 3,
FOR OUTPUT WIRING CONFIGURATIONS.